Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Dallas Homeowners Choose Dvele Construction
Groundwork Construction Co. of Dallas is an independent Dvele construction service provider, working on Dvele modular and prefabricated homes across the Dallas area. We’re a full-scope construction partner for Dvele owners, not a parts-swapper with a generic crew. What makes our Dvele work different: we read Dvele’s factory drawings and chassis/panel connection details before we pick up a tool, so we finish cabinets, tile, showers and roofing around a completed module instead of guessing at tolerances.

For Dallas, that distinction matters more than it sounds. A Dvele home is a closed shell with engineered attachment points already set by the factory. When something shifts a season later – a seam, a cabinet run, a flashing detail – the fix depends on knowing exactly how that shell was built. We do, which is why we service Dvele homes throughout Oak Cliff, East Dallas and the newer infill pockets where prefab is gaining ground.
We’re independent and not authorized by or affiliated with Dvele. That’s a good thing for you. We’ll tell you straight when a repair is the right call and when it’s time to plan a bigger replacement. Call (844) 797-4808 to schedule a free estimate.
Why Trust Groundwork Construction Co. of Dallas for Your Dvele Construction?
Our technicians have up to 12 years of experience working on prefab and stick-built homes, and on a Dvele job that experience shows up in the small things. We know which panel joints carry structural load and which are finish seams, so we anchor millwork into the module’s structural members rather than the closest thing that holds a screw. That’s the difference between a cabinet run that stays put and one that pulls away again after the next wet-dry cycle.
Parts matter too. On Dvele homes we match factory-specified or OEM-equivalent hardware, flashing and sealant systems first. Off-spec parts fight the module’s engineered tolerances – a sealant that’s too stiff or a flashing that doesn’t match the low-slope roof assembly will fail faster than the factory detail ever would. Getting the part right protects the envelope and keeps your build consistent with the factory design.
Every repair and install we do is warranty-safe and covered by our 730-Day Done Right Promise. If it’s not done right, we make it right – for two full years, in writing. No voicemail black holes either: calls are answered by a live person, 24/7. And every technician is background-checked and arrives in uniform, so you know who’s on your property.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Common Dvele Construction Problems We Fix in Dallas
Dvele self-powered modular and panelized homes are built to tight tolerances. That precision is an asset until the seams start moving, and in Dallas’s hot, humid summers and hard spring windstorms, they will move. Here’s what we see most, and why each one happens:
- Module-to-module and module-to-foundation seams opening. As the chassis settles over its first few seasons of thermal movement, marriage lines can open just enough to let water past. The fix is a proper re-flash and re-seal at the seam that respects the factory’s connection detail, not a bead of caulk smeared over the gap.
- Factory cabinet and millwork boxes racking or pulling from walls. A Dvele panel wall flexes seasonally, and a cabinet box anchored to finish material instead of the structural member pulls loose. This is a common reason a kitchen run on a prefab home starts to gap at the wall within a couple of dry summers.
- Roof-to-wall transition and penetration flashing on low-slope prefab roofs. Low-slope roof assemblies channel water to specific points, and a transition detail that wasn’t built for Dallas hail and wind-driven rain will leak right into the envelope. Re-flashing the transition is almost always the right first move.
- Condensation and finish cracks at panel joints from tight envelopes. Dvele’s high-performance envelope packages are heavily insulated and tight, which is the point – but if ventilation is undersized for the home’s humidity load, moisture gets trapped and shows up as condensation, blistering or hairline cracks at the joints. The repair fixes the ventilation source, not just the paint.
- Shower pan and wet-area failures in modular bath cores. Dvele’s modular bath core is set up in the factory, so any movement at the pan edge or curb shows up as a seam failure. Rebuilding the pan and waterproofing it to the module’s tolerances fixes it; a surface patch doesn’t.
What ties these together is the reason a Dvele home needs a different approach than a stick-built Dallas house. A Dvele module is a finished shell the day it lands. There’s no open framing to sister a joist to or shim a stud against. Our job is to work with the engineered attachment points the factory already established, so we catch the actual failure mode instead of treating a symptom.
Dvele Parts & Our Repair-vs-Replace Approach
On Dvele homes we match factory-specified or OEM-equivalent parts first – cabinet hardware, flashing systems, sealant types – because off-spec components fight the module’s engineered tolerances. We source parts for each job based on what the factory drawings call for, so you’re not getting a generic part that happens to fit. We don’t claim to stock Dvele parts locally; we order what the job needs.
Our repair-vs-replace call is honest. Where a component has failed – a seam, a racked cabinet run, a shower pan – we favor targeted repair and re-flashing over wholesale replacement, unless the substrate underneath is actually compromised. If the wood or panel behind a leaking transition is soft, patching the surface is throwing money at a bigger problem, and we’ll show you why. You get upfront pricing with no surprises: the number you see is the number you pay.
Not sure whether your Dvele issue is a repair or a replacement? Call (844) 797-4808 and we’ll walk you through it – estimates are free.
Our Dvele Service Process – Step by Step
- 1
Diagnosis. We review the Dvele drawings and inspect the specific seam, cabinet run, roof transition or bath module involved. On prefab homes we look for movement at the marriage lines and panel joints first, since that’s usually where the real cause lives.
- 2
Repair or install. We re-flash and re-seal transitions, re-anchor millwork into the module’s structural members, and install showers and cabinets to the factory’s tolerances. Parts are OEM-specified or equivalent.
- 3
Test. Water-testing at re-flashed transitions, pull-testing anchors, and checking ventilation and humidity in tight envelope areas. We confirm the fix holds before we call it done.
- 4
Warranty. Every Dvele job is backed by our 730-Day Done Right Promise. If it’s not done right, we make it right – in writing, for two years.
See the difference
Before
After
Before
After
Before
AfterDvele Products We Service & Install in Dallas
We work across Dvele’s self-powered modular single-family homes – the net-zero ready platform – as well as Dvele prefabricated panelized wall and roof assemblies, modular kitchen and bath core modules, and Dvele high-performance envelope packages. In practice that means we service and install the components that live inside and on top of those modules: cabinets and refacing, walk-in showers and shower remodeling, and roof repair and re-flashing on the low-slope prefab roof assemblies.
Dvele Service Pricing in Dallas
Here’s what Dvele-related work typically runs in the Dallas market. Every job is quoted upfront, and your number doesn’t change once work starts.
| Service | Typical Dallas Range |
|---|---|
| Cabinet Installation | $4,000 – $13,000 |
| Walk-In Shower Installation | $4,500 – $12,000 |
| Roof Repair | $400 – $1,800 |
| Roof Replacement | $8,000 – $20,000 |
| Bathroom Remodel | $9,000 – $28,000 |
We Also Service These Brands
Groundwork is a multi-brand construction partner, not a single-brand shop. Alongside Dvele, we work with KraftMaid and Cambria on kitchens, Silestone on countertops, and Kohler on fixtures – plus GAF and CertainTeed on roofing, Andersen and Pella on windows, and James Hardie and Belgard on exteriors. If your Dvele home has material from any of these brands, we can service it alongside the Dvele envelope work in one visit.
FAQs – Dvele Construction Service in Dallas
Yes. Because we read the factory drawings and work to the module’s attachment points and tolerances, our cabinet and bath work leaves the envelope design intact. We don’t cut into panels or re-route the high-performance envelope to make something fit. Call (844) 797-4808 to talk through your project.
Because a Dvele home is a closed, engineered shell instead of an open frame, so seasonal thermal movement shows up directly at the panel joints and cabinet-to-wall connections. A stick-built house flexes across an assembly of many pieces; a prefab module moves as a more unified shell. That’s why millwork has to be anchored into the structural members, and why we re-anchor rather than simply re-caulk.
We re-flash and re-seal the transition to match the factory’s low-slope roof assembly rather than patching the leak point. A transition detail that wasn’t built for Dallas hail and wind-driven rain will keep leaking, so we fix the detail, then water-test it. Roof repair in Dallas typically runs $400 – $1,800. Call (844) 797-4808 for an exact quote – estimates are free.
Yes. We rebuild and install walk-in showers within the modular bath core, waterproofing to the module’s tolerances – which matters because factory-set pans and curbs fail at the seams if movement isn’t accounted for. Walk-in shower installation in Dallas typically runs $4,500 – $12,000, and a full bathroom remodel $9,000 – $28,000. Call (844) 797-4808 to schedule your free estimate.
No. Groundwork Construction Co. of Dallas is an independent Dvele service provider, not authorized by or affiliated with Dvele. Our credibility comes from working on completed modules and knowing how they’re built, not from a manufacturer badge. We’re a full-scope construction partner, and every job is covered by our 730-Day Done Right Promise.
For the Dvele work we do most: cabinet installation runs $4,000 – $13,000, walk-in shower installation $4,500 – $12,000, roof repair $400 – $1,800, roof replacement $8,000 – $20,000, and a full bathroom remodel $9,000 – $28,000. Every job is quoted upfront with no surprises – the number you see is the number you pay. Call (844) 797-4808 for an exact quote – estimates are free, and 0% financing for 18 months is available, with $1,000 off projects over $10,000.
Book Your Dvele Service in Dallas, TX
If your Dvele home has a seam that’s opened, a cabinet run pulling loose, a leaking roof transition, or a bath module ready for a real walk-in shower, Groundwork Construction Co. of Dallas can help. You’ll get a live person on the line 24/7, a uniformed, background-checked technician on the job, and upfront pricing with no surprises – all backed by our 730-Day Done Right Promise. Call (844) 797-4808 to schedule your free estimate and design consult.
Written by the team at Groundwork Construction Co. of Dallas.