Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
KraftMaid Fence Installation: The Dallas Owner’s Guide
We install and replace fence systems matched to KraftMaid specifications in Dallas, and complete installations typically run $3500 – $9000 depending on fence length, material and site conditions. Most standard residential runs are finished in a single visit. If you’re reading this, your fence has likely failed in one of the familiar ways Dallas owners describe: a section sagging after a storm, posts leaning in black clay soil, or boards that have split and gone chalky after one too many 100-degree summers. We’re an independent installer and not affiliated with KraftMaid, but we know this product line closely and price the work honestly.

Which KraftMaid Models This Applies To
KraftMaid’s fence systems follow the same material and finish logic as the cabinetry line, which matters when you’re matching a replacement to an existing run. The two compatibility gotchas we run into most in Dallas homes: post spacing that was set at a non-standard 6-foot or 7-foot interval rather than the usual 8-foot on-center, and finish codes that changed between product generations, so a “matching” panel from a newer batch can read slightly lighter or darker in bright Texas sun.
How to confirm what you have before ordering or replacing:
- Find the specification label on the interior face of an end post or gate jamb.
- Measure actual post spacing, not just total run length; that number drives every panel.
- Note the finish code and material grade so your replacement matches the existing line.
- Photograph the failed section next to a tape measure; it saves a return trip.
On the OEM-versus-aftermarket call: a genuine KraftMaid-matched component protects the look of the whole run and is worth it when the fence is largely intact. Where a single panel or post has failed, a quality aftermarket equivalent at the same specification often does the job at a lower cost, and we’ll tell you plainly which way the math goes.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your KraftMaid Fence Installation Is Failing
Dallas weather is hard on fences. Between the shrink-swell clay under most lots and the UV load from June through September, failure shows up in predictable patterns. Here’s what to watch for and why each one happens.
- Posts leaning or heaving after rain. The black clay soil expands and contracts with moisture, pushing posts out of plumb. Once a post is loose, the panels it holds start to rack.
- Boards splitting or checking along the grain. Rapid wet-dry cycling dries the material unevenly. Surface cracks that start small become structural splits within a season or two.
- Finish fading or chalking to a dull grey. Intense Texas sun breaks down the protective finish. Once it chalks, the material underneath is unprotected and ages fast.
- Sagging gates and sticking latches. A gate that drags is usually a sign the hinge post has shifted or the frame has warped. It gets worse, never better, without correction.
- Loose or missing fasteners along a run. Corrosion and wood movement work fasteners loose over time. A fence held together by a few remaining screws is one storm from a section coming down.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Dallas, fence installation and replacement generally lands between $3500 and $9000. The range is driven by total linear footage, material grade, number of gates, post-setting depth and whether old material needs hauling off. Vinyl runs tend to sit toward the lower half of that range; aluminum and premium finishes push toward the top.
What the number should cover, every time:

- Removal and disposal of the failed section or full run.
- New posts set to proper depth for Dallas clay, not just dropped in a hole.
- Matched panels, rails and hardware at the correct spacing.
- Cleanup and a walkthrough before we leave.
Upfront pricing means the number you see is the number you pay. Every installation is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. We’ll also apply the standing $1,000 off projects over $10,000 and 0% financing for 18 months where they fit your project.
DIY or Call Us?
Some things you can safely handle yourself. Walk the run, photograph the failed section, measure post spacing, note the finish code and check for loose fasteners. That information makes a replacement quote fast and accurate.
Where DIY goes wrong: setting posts in Dallas clay without proper depth and drainage. A post that isn’t set correctly heaves within a season, and a fence built on a bad post line looks the same as a failed one. Panels installed out of plumb put stress on every adjacent section. And when a run is long or the ground is uneven, matching grade across posts is where most owner-built fences start to wobble. Our technicians have up to 12 years of experience on this work, and they’re background-checked and arrive in uniform. Call (844) 797-4808 to talk it through; a live person answers around the clock.
FAQs
How long does a KraftMaid fence installation last in Dallas? A properly installed fence in Dallas typically lasts 15 to 20 years for vinyl and longer for aluminum, though the black clay soil and summer UV shorten the low end. Post-setting quality is the single biggest factor in how long it actually holds.
Can a failing section be repaired instead of fully replaced? Yes, often it can. If the posts are sound and only a few panels or boards have failed, a targeted repair usually makes more sense than a full run replacement. We’ll assess it honestly and quote the smaller job if that’s the right call.
How long does the swap take? A standard residential fence section or short run is usually finished in a single visit. Longer runs or runs needing new posts set in clay may span two visits. We confirm the timeline in the written quote before any work starts.
How do you source the KraftMaid part? We match the replacement to your model’s specification label and finish code, then source from verified suppliers at the correct grade. If a genuine KraftMaid-matched component is right for the job, that’s what we order; if a quality equivalent at the same spec saves you money, we’ll tell you and let you decide.
We also work with Cambria, Silestone and Kohler on the interior side, and the same upfront-pricing and 730-Day Done Right Promise apply across every service line. Call (844) 797-4808 to schedule your free project estimate and design consult. Calls are answered by a live person, 24/7, and no-hassle upfront pricing means no surprises at the end.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.