Home additions & ADU
Kitchen remodeling
Bathroom remodeling
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Kohler Home Additions & ADU: The Dallas Owner’s Guide
We build Kohler-appointed home additions and ADUs in Dallas, and a typical finished addition runs $45,000 – $130,000, with detached ADUs at $90,000 – $220,000. Projects are planned, permitted and scheduled, and we walk you through a free design consult before a single number is fixed.

Owners in Dallas usually come to this page after a specific moment: the bid they got was one page long and didn’t say what was inside the walls, or the crew that promised a spring start stopped answering calls in June. The Kohler side comes in when you’ve picked the fixtures for the new bath or kitchen and want to know whether the brand you trust in the showroom actually means anything on a Dallas job site. It does, but only if the plumbing rough-in, the venting and the water pressure are planned around those fixtures instead of after the fact. That planning gap is where most additions in Dallas quietly go over budget.
- Kohler fixtures are the easy part. The hard part is the slab, the drainage and the City of Dallas permit sequence.
- Upfront pricing, no surprises means a line-item scope you can read before you sign, not a lump sum with allowances buried inside.
- The 730-Day Done Right Promise covers our workmanship for two full years, which matters more on an addition than on any other job we do.
Which Kohler Models This Applies To
Kohler doesn’t sell an “ADU line,” so the compatibility question is really about which Kohler product families we plan around in a new addition. In a Dallas addition bath, that usually means Kohler’s Memoirs, Archer and Corbelle toilet families, the Fairfax and Loure faucet collections, and Choreograph or Bellwether shower bases. In an addition kitchen or kitchenette, it’s the Iron/Tones and Whitehaven sinks, the Crue and Purist faucets, and Kohler’s undercounter filtration systems.
How you identify the right part is the same whether you’re matching a toilet fill valve or picking a shower valve for rough-in:
- Find the model number on the inside of the tank lid or the back of the fixture. Kohler stamps it there, and a photo of the lid is usually enough for us to match it.
- Measure the rough-in on toilets (the distance from the finished back wall to the closet flange bolts). Most Dallas homes built after 1980 run 12 inches, but older East Dallas and Oak Cliff houses regularly run 10 inches, and a 12-inch toilet won’t fit a 10-inch rough-in.
- Check the valve series on showers. Kohler’s Rite-Temp pressure-balancing valves and their newer thermostatic valves use different trim, and the trim from one won’t seat on the other.
On the OEM-versus-aftermarket question: for Kohler fill valves, flush valves and cartridges, we install Kohler genuine parts. The aftermarket equivalents cost a third as much and fail two to three times sooner in our experience, and on a new addition those parts sit behind a finished wall. We’re an independent construction company, not affiliated with Kohler, so when we recommend a Kohler part it’s because we’ve installed it, not because we’re obligated to. We also spec KraftMaid cabinetry, Cambria and Silestone counters alongside Kohler fixtures when the scope calls for it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Kohler Home Additions & ADU Is Failing
An addition isn’t a part that fails, but the Kohler systems inside it do, and they fail in patterns we see over and over in Dallas. Here’s what to watch for:
- A toilet that runs for a few seconds every hour. That’s usually a Kohler fill valve with a worn seal, and it’s wasting water every day it goes unfixed. In a Dallas summer, a slow leak like this can add noticeably to your water bill before you notice anything else.
- A shower that loses temperature when someone flushes. A Rite-Temp pressure-balancing cartridge that’s scaled up or stuck. Dallas water runs hard, and the cartridge in a new addition bath can scale within three to four years if the valve isn’t serviced.
- Water pooling at the base of a shower or around a toilet flange. On a slab-on-grade addition, this is often a rough-in issue from the original install, not a fixture problem. Dallas’s expansive clay soil shifts with our wet-dry cycles, and a poorly bedded drain line will move with it.
- Cabinet doors that won’t stay shut or drawers that drag. Usually humidity, not hinges. Additions in Dallas need the HVAC balanced for the new square footage, or the cabinetry swells through the summer.
- Cracks at the corner where the addition meets the original house. A foundation or framing issue, and one that needs eyes on it sooner rather than later. Clay soil and a poorly tied-in addition are a known combination in Dallas.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s what adds up in Dallas, with the caveat that every addition is priced from a written scope, not a square-foot guess:
| Scope | Typical installed range |
|---|---|
| Home Addition (Kohler-appointed bath or kitchen) | $45,000 – $130,000 |
| ADU Construction (detached or attached) | $90,000 – $220,000 |
| Garage Conversion | $30,000 – $80,000 |
What drives the range: foundation type and soil conditions, whether a slab has to be cut or a new stem wall poured, roof tie-in and matching, electrical service capacity, and how many Kohler fixtures land in the plan. A single addition bath with a Kohler Memoirs toilet and a Kohler shower valve sits at the low end; a full kitchenette with Kohler sink and faucet, KraftMaid cabinetry and a Cambria counter moves toward the middle and up.
What’s included in our number: permit drawings, City of Dallas permits and inspections, demolition, foundation, framing, mechanical and electrical, finishes and Kohler fixture installation. What’s not: allowances we haven’t agreed on. The number you see is the number you pay, and the work carries the 730-Day Done Right Promise.
DIY or Call Us?
What you can safely check yourself: the model number on a Kohler toilet lid, whether a shower cartridge is scaling up, and whether a cabinet door hinge is loose. Photograph what you find and note it, and it’ll save time on the first call.
Where DIY goes wrong on an addition: framing, foundation, roof tie-in, electrical and plumbing rough-in. These are permitted work in Dallas, and a homeowner-permitted addition that fails inspection can cost more to correct than it would have cost to build right the first time. A missed flashing detail at a roof tie-in can leak for a season before you see a stain. A Kohler shower valve installed against the wrong rough-in depth will leak inside the wall, not at the trim, so you won’t notice until the drywall is soft.
If you’re priced, permitted and comparing bids, call us. We’ll show you a line-item scope and price it honestly. Call (844) 797-4808 for a free estimate.
FAQs
Kohler’s ceramic and vitreous china fixtures commonly last 20 years or more, while the moving parts inside them – fill valves, flush valves, cartridges – typically last 5 to 10 years in Dallas water. Scaling from our hard water shortens that, and servicing the valve every few years extends it. Call (844) 797-4808 for an exact quote on replacement – estimates are free.
Often, yes. A running Kohler toilet is usually a $20 to $60 fill valve or flapper, not a new toilet. A shower that won’t hold temperature is usually a cartridge. We’ll tell you plainly when a repair is the right call and when it isn’t. Call (844) 797-4808 for a free estimate.
A single Kohler fixture swap is usually an hour or two, and most jobs we do are completed in a single visit. A shower valve replacement means opening the wall, replacing the cartridge or valve body, and patching, which is typically a half-day to a full day. A full addition is a multi-month project with a written schedule. Call (844) 797-4808 to schedule your free estimate.
We match from the model number stamped on the fixture, verify the rough-in and valve series, and order the Kohler genuine part for your specific model. We don’t carry parts on a truck, so the part arrives for your scheduled install, which is why the model number matters on the first call. Call (844) 797-4808 for a free estimate.
Whatever stage you’re at – a failing Kohler fixture in an existing addition, or a plan on paper for a new one – we’re happy to look at it with you. Every project starts with a free design consult and estimate, all work is covered by the 730-Day Done Right Promise, and we offer 0% financing for 18 months plus $1,000 off projects over $10,000. Calls are answered by a live person, 24/7. Call (844) 797-4808 to get started.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.