Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Windows & Doors: The Dallas Owner’s Guide
We install CGI-compatible windows and doors for Dallas homeowners, priced by unit and by opening: impact window installation runs $8,000 – $25,000 and standard window replacement runs $4,500 – $15,000, depending on how many openings, which series you’re matching, and whether the framing is sound. Every project is covered by our 730-Day Done Right Promise. Most owners land here after the failure makes itself known: a multi-point lock that no longer catches, a door slab that drags its bottom corner across the threshold, or a fogged glass unit that has been hazy since the first hard Dallas summer. Those are the three loudest symptoms, and each points to a different part inside the same assembly.

Which CGI Models This Applies To
CGI makes aluminum-framed impact windows and door systems, and much of what stands in Dallas homes came out of the builder-grade side of that catalog: sliding glass doors, single-hung and horizontal sliders, and swing doors with multi-point hardware. The part you need is often shared across several model lines rather than unique to one, which is good news. Identify your unit before ordering anything. Pull the manufacturer label off the head jamb or the glass spacer and photograph it. If the label is gone, measure the visible glass width and height, the frame depth from interior to exterior, and the distance between hinge screws; a supplier can usually match from those three numbers alone.
Here’s the decision most people get wrong: aftermarket hardware is fine for rollers, weatherstripping, sweeps and handles, but the lock and multi-point gear should be OEM or an exact-function equivalent. The gear geometry has to line up with the strike plates already cut into your frame, and a near-match will leave the door looking shut while the deadbolt floats a quarter inch from engagement. We’re an independent service provider, not affiliated with CGI, and we’ll tell you plainly when an aftermarket part is the smarter buy and when it isn’t.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Windows & Doors Is Failing
- The lock won’t engage or pops open with a push. The gear has worn or the door has shifted on its hinges, so the bolt no longer lines up with the strike. Left alone, this is a security gap, not a nuisance.
- The door drags or scrapes at the bottom corner. A sash that sags is usually a hinge problem or a frame that has racked; the weather seal fails next once the gap opens.
- Fog or a milky haze between the panes. The hermetic seal on the insulated glass unit has broken, and moisture has entered the cavity. No amount of cleaning fixes this, and it gets worse with every Dallas temperature swing.
- Sliders that need two hands and a shoulder. Worn rollers, a flattened track, or both. Rollers are cheap; the track replacement is the part that gets missed.
- Drafts, water staining, or daylight at the frame. Weatherstripping and corner seals have perished, which in Dallas heat and summer storm driving rain leads to water behind the frame.
One reality worth knowing: in Dallas, west and south-facing units take far more sun load than the shaded sides of the same house. If one side of the home is failing and the other isn’t, that’s normal. It’s solar exposure, not a bad install.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Window and door pricing in Dallas is quoted by line item so you can see what you’re paying for: the unit or part, the labor, disposal, and any frame repair discovered once the old piece is out. Impact assemblies run $8,000 – $25,000 installed for a typical home, while standard window replacement runs $4,500 – $15,000. What moves you up or down the range: number of openings, impact-rated versus standard glass, frame condition, and whether the rough opening needs work. We quote upfront, and the number you see is the number you pay. The work itself carries the 730-Day Done Right Promise, written, not implied.

DIY or Call Us?
You can safely do the reconnaissance yourself: photograph the label, feel for daylight around the frame, test the lock with the door closed, and note which openings face west or south. That’s information a technician will want anyway. Where owners get into trouble is replacing the door gear or trying to re-hang a racked frame alone, because a mismeasured part means a second trip, a second purchase, and a door standing open in the meantime. Glass units are a straight call-out job.
Call (844) 797-4808 and a live person picks up, any hour. Free estimates, no-hassle upfront pricing, and 0% financing for 18 months available.
FAQs
Expect 15 to 25 years from the frame and glass, and far less from hardware: rollers and weatherstripping typically give you 8 to 12 years under Dallas heat before they need attention, and multi-point locks can wear sooner on doors used daily. Call (844) 797-4808 for a free estimate on the parts that are actually worn.
Often yes. Rollers, sweeps, weatherstripping and handles are straightforward replacements; a lock gear can frequently be swapped without touching the door. A fogged insulated glass unit or a racked frame usually means full replacement of that unit. We’ll tell you which one you’re facing before you commit to anything.
Most hardware jobs finish in a single visit, an hour to two per opening. Full window or door unit replacement runs a few hours per opening once the opening is opened up. We’ll give you the time estimate in writing with the quote.
We match on the label or, if it’s gone, on measured glass size, frame depth and hinge spacing, then pull OEM or exact-function equivalents through our supplier network. You don’t order anything yourself; we verify fit before the part is ordered. Call (844) 797-4808 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.