Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Kitchen Remodeling: The Dallas Owner’s Guide
Quick answer: We install Unilock-compatible kitchen remodeling for Dallas homeowners, with full kitchen projects typically landing between $14,000 and $45,000 depending on scope, materials and layout. There’s no same-day turnaround on a kitchen – this is planned construction, not an emergency repair, and we won’t pretend otherwise. Most Dallas jobs run two to six weeks once materials are staged.

Owners usually discover a problem the same way. A cabinet door starts rubbing after a summer of swelling and shrinking. A countertop seam near a sink shows a hairline crack. A drawer that once glided now catches halfway out. The kitchen still works, so nobody panics. Then a small failure starts spreading – water finds the seam, the gap widens, and a part that could have been swapped becomes a run of cabinets or a whole surface. That drift is the expensive part.
We’re Groundwork Construction Co. of Dallas, an independent service provider and not affiliated with Unilock. We connect Dallas homeowners with independent local professionals who do the actual installation, all covered by our 730-Day Done Right Promise.
Key Takeaways
- Full Unilock-compatible kitchen work in Dallas: $14,000-$45,000 installed.
- Cabinet installation alone: $4,000-$13,000. Countertops: $2,000-$6,500.
- North Texas heat cycling is hard on cabinet boxes and door hinges – expect faster wear than coastal or mild-climate homes.
- Every project carries upfront pricing, and the number you see is the number you pay.
Which Unilock Models This Applies To
Unilock is best known for hardscape, but the brand also shows up in kitchen-facing product lines, and owners arrive at this page holding one of a few kinds of part. Each requires a different matching approach.
Cabinet and door hardware. If your Unilock kitchen uses branded hinges, drawer slides or a handle system, match on the hinge cup diameter and the slide length – not the finish. A 35mm cup hinge is standard, but a 26mm cup exists on older and imported boxes, and the two don’t swap. Measure the cup bore with calipers before you order anything.
Countertop and surface edges. Unilock quartz and surface products use a branded edge profile and a specific seam adhesive. Aftermarket edge strips of the same color name rarely match lot-to-lot; quartz color varies by production run, and a mismatched edge shows in raking light.
Trim and fillers. Panel and filler parts are matched to cabinet finish and door style codes. The style code lives on a label inside the cabinet door or on the back of a drawer box, and it matters more than the color name.
OEM versus aftermarket. For a hinge or slide, a quality aftermarket equivalent from a known brand is a defensible choice – the loads are low and the failure modes are known. For anything visible – edges, fills, panels, doors – go OEM. Color and profile matching is where aftermarket quietly fails, and it fails visibly.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Kitchen Remodeling Is Failing
These are the symptoms we hear most from Dallas owners, with the cause underneath each one.
- Doors that rub or won’t close flush. The hinge has lost tension or the cabinet box has twisted with seasonal movement. North Texas humidity swings from winter to summer push MDF and particle boxes harder than the maker’s spec assumes, and a box out of square by a few millimeters is enough to bind a door.
- Drawers that catch or feel gritty. The slide is worn or the mounting screws have pulled loose from the box. Once a screw hole strips in particle board, the slide rarely stays true no matter how many times you tighten it.
- Hairline cracks at a countertop seam or near the sink cutout. Seam adhesive has failed, or the surface wasn’t supported properly under the cutout. Left alone, water wicks into the seam and the crack widens through freeze-thaw cycles.
- Swelling, darkening or soft spots at the base of a cabinet. Moisture is reaching the toe kick or the box bottom, usually from a slow sink or dishwasher leak. Soft, spongy cabinet board can’t be patched – it has to be replaced.
- Loose or lifting backsplash tile. The bond has broken down or the substrate moved. A single loose tile near a wet area signals the issue runs deeper than one piece.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing for Dallas, with the parts and labor together rather than split out to confuse the comparison:
| Work | Installed range |
|---|---|
| Full kitchen remodel | $14,000-$45,000 |
| Small kitchen remodel | $9,000-$20,000 |
| Cabinet installation | $4,000-$13,000 |
| Countertop installation | $2,000-$6,500 |
| Backsplash installation | $800-$2,500 |
| Kitchen island installation | $3,000-$10,000 |
What drives the range is box count, finish and door style, whether the layout changes (which pulls electrical and plumbing), and whether you go OEM or aftermarket on visible parts. Every quote from us is written line by line, and the number you see is the number you pay – no change orders that appear mid-job. Work is covered by the 730-Day Done Right Promise, one of the longer workmanship guarantees in residential construction.
DIY or Call Us?
You can safely measure and document. Open the cabinet door and photograph the label inside, measure the hinge cup bore, measure the drawer slide length, and check that the cabinet box is square with a framing square. That information makes every quote more accurate.
Where DIY goes wrong: swapping a slide or hinge on a box that’s already out of square, or replacing a counter seam on a surface that isn’t properly supported. Both look like a simple part swap and turn into a bigger repair within a season. And if the failing part is connected to the sink or dishwasher plumbing, stop and call – a slow leak behind a cabinet causes more damage than the cabinet part ever would.
Call (844) 797-4808 for a free estimate. A live person answers around the clock, and the technician who comes out is background-checked and in uniform.
FAQs
Hardware like hinges and slides typically runs 10 to 15 years in a climate-controlled kitchen, and North Texas heat cycling shortens that – the other six to eight months wear the components faster because wood and MDF expand in summer and contract in winter. Expect half that lifespan on a cabinet facing a kitchen that gets full afternoon sun. Call (844) 797-4808 for an exact quote – estimates are free.
Sometimes. A hinge can often be re-tensioned or replaced, and a single slide can be swapped without touching the cabinet. But a soft or swollen cabinet box or a failed countertop seam usually needs replacement, not a patch, because the underlying problem doesn’t stop at the part. We’ll tell you plainly which it is during the estimate.
A hardware or single-part swap is often done in one visit. A cabinet run or countertop replacement takes longer – typically a few days, with countertop fabrication and templating adding time. We give you the realistic schedule before you commit, not after.
We match the style code and finish from the label on your cabinet, then source through a verified Unilock-compatible supplier. We don’t stock parts locally – each part is ordered to your spec, which is why accurate measurements matter. We also install KraftMaid, Cambria and Silestone for owners comparing options.
One note on parts and pricing overall: Groundwork connects you with independent local professionals who do the work. The 730-Day Done Right Promise covers workmanship. Calls are answered live 24/7, technicians are background-checked and uniformed, and financing is 0% for 18 months with $1,000 off projects over $10,000.
Call (844) 797-4808 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.