Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Farmers Branch, TX: What the Job Actually Involves
Metal roofing in Farmers Branch usually runs $15,000 to $40,000 for a full residential install, and most homes are weather-tight in five to nine working days. The job means stripping the old shingles, checking and repairing the deck, laying down underlayment and a wind-rated panel system, then flashing and trimming it out. Older 1950s to 1970s ranch stock here sometimes hides rotten sheathing under worn shingles, which is the one thing that can stretch the schedule. Call (844) 797-4808 for a free on-site estimate.
How We Run a Metal Roofing Job, Start to Finish
No two roofs go the same way, but the sequence below is what a Farmers Branch metal roofing project looks like from the first morning to the final inspection.
- Day 1 – tear-off and deck inspection. We strip the existing roof down to the sheathing and walk every sheet. Any soft or delaminated decking gets replaced before a single panel goes down. You’ll know the deck condition and the exact replacement count by end of day. Most homes don’t need more than a few sheets.
- Day 2 – underlayment and edge metal. We roll out a high-temp synthetic underlayment rated for metal’s heat cycle, then set drip edge and rake trim. This is also when we map out panel layout and confirm where the valleys and penetrations land. This is your last easy chance to change panel color if you’ve been going back and forth.
- Days 3 to 6 – panel installation. Panels go up in order, screwed through the ribs at the fastener spacing the wind rating calls for. Standing seam panels run longer and slower than exposed-fastener panels, so a simple gable roof may finish panels in two days while a cut-up hip roof with dormers can take four.
- Day 6 or 7 – flashing and penetrations. Vents, chimney surrounds, skylights and wall transitions get their own formed flashing. Every penetration is a leak waiting to happen, so we don’t rush this stage.
- Final day – cleanup and inspection. Magnetic sweep of the yard, gutter clearing, a final walkthrough with you on the ground while we’re still on the roof. Then we call for inspection if the scope requires it.
As part of a full Roofing in Farmers Branch scope, we sequence metal over the top of any attic insulation or structural work so the trades aren’t stepping on each other. If you want to see the wider set of roof work we handle, our Roofing service covers it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Metal Roofing Choices That Actually Matter to You
The material decision drives most of the cost and all of the feel of the finished roof. Here’s what’s on the table, with the honest trade-off of each.
- Standing seam steel – the premium option. Hidden fasteners, clean lines, typically 40 to 70 years of life. It’s the strongest wind performer because there are no exposed screws to work loose. Costs more per square and takes longer to install.
- Exposed-fastener steel panels – lower cost, faster install, good for outbuildings, shops and budget-conscious homes. The trade-off is visible screws with rubber washers that can dry out over 15 to 25 years and need inspecting. Fine for a shed; less ideal on the house you plan to keep.
- Aluminum panels – lighter, rust-proof, and a strong choice near coastal-influenced humidity, though on a North Texas roof the weight savings matter less. Higher material cost than steel.
- Stone-coated steel – looks like tile or shake but installs as panels. Popular on homes that want the metal performance without the modern industrial look. Heavier and a middle price point.
- Paint finish and color – a Kynar-type finish holds color far longer than a basic acrylic. Light colors reflect more heat, which matters on a Texas roof that bakes from May to September.
What Metal Roofing Costs in Farmers Branch, TX
Expect $15,000 to $40,000 for a full metal roof on a typical Farmers Branch home, or roughly $9 to $16 per square foot installed. That’s the real working number and it’s what you’ll see on a written estimate, not a teaser.
Five things push a job toward the low or high end of that range:
- Roof size and pitch. A simple gable is cheaper per square than a steep hip roof with valleys and dormers, because every cut slows the crew.
- Deck condition. A 1960s roof with soft sheathing means new plywood, and that’s usually a few hundred to a couple thousand dollars depending on how much turns up.
- Panel type and gauge. Standing seam aluminum sits at the top; exposed-fastener steel at the bottom.
- Number of penetrations and valleys. Every vent stack and chimney adds formed flashing and labor.
- Permit and inspection scope. Farmers Branch enforces permits on roof work, and a full re-roof with deck replacement is a larger inspection package than a straightforward overlay.
A written estimate from us lists tear-off, underlayment, panel material, flashing, cleanup and permit line by line, with the number fixed and no change orders unless you ask for a change. What it doesn’t include: structural repairs discovered mid-job (we price those separately and you approve them before we proceed), tree trimming for access, or gutter replacement if the existing gutters can’t take the new roof edge. Background-checked, uniformed technicians handle the install, and everything’s backed by our 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat Farmers Branch Homes Specifically Do to This Job
Farmers Branch is a built-out inner-ring suburb (ZIP 75234), so most of the roofs we metal here go onto existing stock, not new construction. That matters because the housing near the Dallas line is largely mid-century ranch and small post-war cottages from the 1950s to the 1970s, and those roofs have been re-covered two or three times over the decades. Layered shingles mean a full tear-off before any metal goes down, and a full tear-off is where the surprises live: old skip sheathing, occasional rot at the eaves, and fasteners that never matched the original structure.
The clay soil underneath doesn’t shake a roof directly, but it does mean additions and rebuilds here get engineered for movement, and the roof has to meet framing that’s been tied into that engineering. On the weather side, this is hail and straight-line wind country. Metal holds up far better than shingle in a serious spring storm, but only if the panel wind rating, the fastener pattern and the edge and valley flashing are all specified for high wind. We spec the system that way by default. On homes near the Valley View and I-35E corridor, tighter lots also mean we plan material staging carefully, since there’s no side yard to speak of. Homeowners here who are also replacing glazing often pair this with Window Replacement in Farmers Branch so the whole envelope gets brought up to wind-ready spec at the same time, and we cover the full Farmers Branch area.
Serving Farmers Branch, TX – Our Local Coverage Area
We serve Farmers Branch and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Farmers Branch
Most Farmers Branch metal roofing jobs finish in five to nine working days once material is on the ground. Simple gable roofs run toward five, and steep or cut-up roofs with dormers and multiple valleys run toward nine. Call (844) 797-4808 for a firm timeline after we’ve seen the roof.
Yes, Farmers Branch requires a permit for roof replacement, and the inspection scope is larger than most homeowners expect. We handle the permit application and the inspection on your behalf. Call (844) 797-4808 and we’ll walk you through what the local office will want to see.
Only if the decking inspects clean after tear-off. Metal is lighter than shingles in most cases, but it still needs solid sheathing underneath, and a 1960s sheathing layer rarely passes without a few repairs. We price the repairs separately and don’t proceed without your approval. Call (844) 797-4808 for a written estimate.
Yes, as long as it’s specified for wind. A standing seam system with the correct fastener spacing and formed edge flashing sheds hail and straight-line wind far better than shingle. Homeowners often pair this with Impact Windows & Doors in Farmers Branch to bring the whole exterior up to storm-spec at once. Call (844) 797-4808 and we’ll talk through wind rating for your specific roof.
Every metal roofing job is covered by the manufacturer’s panel and finish warranty plus our 730-Day Done Right Promise on the workmanship. If something isn’t right within that window, we make it right. Call (844) 797-4808 for the written warranty packet with your estimate.
Schedule Your Free Metal Roofing Estimate
A free on-site estimate for metal roofing in Farmers Branch starts with a phone call to (844) 797-4808. A live person answers, any hour. We’ll set a time to walk the roof with you, measure the squares, check the deck, and hand you a written line-item quote with a fixed price and the permit scope spelled out. No pressure, no vague bids, no surprise line items later.
Written by the team at Groundwork Construction Co.