Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Duncanville, TX: What the Job Actually Involves
Exterior door installation in Duncanville typically runs $1,200 to $5,500 per door installed, and most single-door jobs are finished in one to two working days from demo to final sealant. That range covers everything from a standard steel entry door swap to a fully framed, wind-rated front entry on a 1960s ranch. Interior door replacements land lower, usually $350 to $900 per door hung and cased. Call (844) 797-4808 and we’ll walk your specific door before anyone quotes a number.
How a Door Installation Comes Together, Stage by Stage
Door work punishes shortcuts. A door that looks fine on install day but leaks air or water six months later was cut in wrong from the start. Here’s the sequence we run, and what you’ll be deciding along the way.
Stage 1: Measure and assessment (day of estimate)
We pull actual rough-opening dimensions, check the existing wall for rot, and look at the framing behind the trim. On Duncanville’s older brick-veneer homes, this is where we find out whether the existing opening is square and whether the header is sound. You decide at this point: replace the door in the existing opening, or reframe for a wider or taller opening.
Stage 2: Product selection and ordering (3 to 10 business days of lead time)
Once we know the opening, you pick the door. Standard sizes ship fast; odd widths, custom glass, and impact-rated units take longer. You’ll sign off on the spec sheet and the swing direction. This is the stage that sets your timeline more than any other.
Stage 3: Demo and prep (2 to 4 hours)
Old door and frame come out, and we inspect the rough opening for soft wood, failed flashing, or water intrusion from previous installs. Sill pans get set, and any rot gets cut out and replaced before the new unit goes near the opening. We don’t skip this step to save an hour.
Stage 4: Setting and sealing (3 to 5 hours)
The new unit gets set plumb and square, shimmed, fastened through the frame per the manufacturer’s instructions, and sealed with the right flashing and sealant sequence. We check the reveal, verify the door swings and latches clean with no binding, and confirm weatherstripping contacts all the way around.
Stage 5: Trim, hardware, and walkthrough (2 to 4 hours)
Interior and exterior trim go back on, the lockset and any hardware get installed and adjusted, and we walk the finished door with you. You test the swing, check the seal, and confirm the finish. Most jobs finish in a single day of install after the product arrives.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Choices You’ll Make on a Door Installation
Door selection is where a lot of homeowners get lost, so here’s the honest version of what each option actually gets you.
- Steel entry doors: The common choice for front doors. Strong, holds paint well, resists dents and weather. Cost sits at the lower end of the range. The downside is that steel can rust if the sealant fails, so prep quality matters more than the door itself.
- Fiberglass entry doors: Best balance for North Texas wind and sun. Doesn’t dent, doesn’t rust, holds up to hail. Costs more than steel buts lasts longer here. Textured finishes can mimic wood convincingly.
- Wood doors: Beautiful, warm, expensive, and need regular refinishing in our climate. Suited to covered porches and homeowners who’ll keep up with the finish. Rot risk rises the closer a wood door sits to direct weather.
- Impact-rated and wind-rated units: Required where wind-borne debris risk is high. Heavier, more expensive, and the right answer for exterior doors on exposed elevations. Costs run toward the top of the range.
- Interior doors: Hollow-core for closets and budget rooms, solid-core for bedrooms and bathrooms. Solid-core blocks sound noticeably better. Pre-hung vs. slab: pre-hung is faster to install and usually the right call.
- Hardware and locksets: Standard builder-grade up to smart locks with keypad entry. Hardware runs $80 to $400 on top of the door. Cheap hardware fails first, so this isn’t where we cut.
We carry material brands like Oldcastle for concrete and masonry tie-ins, and we spec doors we know hold up to our summers. Call (844) 797-4808 and we’ll talk through what fits your home and your budget.
What Door Installation Costs in Duncanville, TX
Expect $1,200 to $5,500 for a single exterior door installation in Duncanville, and $350 to $900 per interior door. Here’s what pushes a job up or down.
- Size and configuration: Standard 36-inch single doors sit at the low end. Double doors, sidelights, or transom windows push the range up fast.
- Existing condition: A clean opening on a well-framed wall is a straightforward job. Rot, failed framing, or water damage behind the threshold adds demo and repair.
- Reframing and header work: Widening or relocating a door opening means cutting structure, adding a header, and often touching electrical. That pushes toward the top of the range.
- Material grade: Builder-grade steel at the bottom, fiberglass and impact-rated at the top. Custom wood sits well above.
- Permit scope: New openings and structural changes typically trigger permitting. A simple replacement in the same opening usually doesn’t. We pull permits and handle inspection scheduling on the ones that need it.
A written estimate lists the door unit and hardware, install labor, trim, sealants, disposal, and any prep work uncovered during demo. It does not include finish painting, interior drywall repair beyond the door trim, or HOA approval fees if your HOA has an architectural review. We itemize everything either way, and our 730-Day Done Right Promise covers the workmanship.
See the difference
Before
After
Before
After
Before
AfterWhat Duncanville Homes Specifically Do to This Job
Duncanville is a built-out, largely post-war bedroom city in southwest Dallas County, and nearly every door we install here is a renovation on a 1950s – 1970s brick-veneer ranch, not new construction. That changes the job. Door openings on homes in ZIPs 75116, 75137, and 75138 often sit in walls where the original framing has shifted, and the black clay soils that heave and shrink with our wet-dry cycles have a direct hand in that. We routinely find out-of-square openings, cracked headers, and thresholds that never drained properly. Installers who just shove a new unit into an out-of-square opening deliver a door that binds by year two.
The Duncanville climate adds a second layer. Summers push past 100°F for long stretches, and spring brings hail and straight-line wind. Doors on exposed elevations take real abuse, and we see more storm-damaged door frames and failing weatherstripping here than you’d expect. Wind-rated and impact-rated doors matter for those elevations, not just as a luxury upgrade. If a door installation here is part of a broader storm-resilience project, it pairs naturally with our Windows & Doors in Duncanville scope, and with fencing work homeowners often schedule at the same time, like Chain Link Fence in Duncanville or Vinyl Fence in Duncanville. Our Windows & Doors service covers the full range when the door job is one piece of a bigger plan, and we work all of Duncanville along with DeSoto, Glenn Heights, Lancaster, and Dallas.
Serving Duncanville, TX – Our Local Coverage Area
We serve Duncanville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Door Installation in Duncanville
Most single-door installations wrap up in one to two working days: a few hours of demo and prep, a few hours of setting and sealing, then trim and hardware. Custom or impact-rated units add 3 to 10 business days of lead time before install day. Call (844) 797-4808 for a firm timeline on your door.
Replacing a door in an existing opening typically does not need a permit, but new openings, structural changes, or wind-rated exterior doors often do. We check the scope on every job and pull permits where they’re required, then handle the inspection scheduling. Call (844) 797-4808 and we’ll confirm what your installation needs.
Yes, if the existing opening is sound. Replacing a door in its current frame avoids plumbing and structural work entirely. Reframing a wider opening or shifting a door location means cutting structure and possibly moving electrical, which changes both the timeline and the cost. Call (844) 797-4808 and we’ll size your opening before we quote.
Exterior doors run $1,200 to $5,500 installed, and interior doors run $350 to $900 each. The number moves with size, existing condition, material grade, and whether permits and reframing are involved. Call (844) 797-4808 for an exact quote on your specific door.
Every door we install is covered by our 730-Day Done Right Promise. If the install isn’t right, we make it right, and that covers the workmanship behind the door. Product warranties come separately from the manufacturer. Call (844) 797-4808 to talk through the details.
Get a Free Estimate on Your Duncanville Door Installation
If you’re pricing a door installation in Duncanville, the smart move is to get the opening measured before anyone quotes a number. Call (844) 797-4808 for a free on-site estimate. We’ll look at the rough opening, talk through material options, and give you a written itemized estimate with no surprises. The number you see is the number you pay, and our 730-Day Done Right Promise backs the work. Calls are answered by a live person, 24/7.
Written by the team at Groundwork Construction Co..