Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Asphalt Driveways & Resurfacing in Cedar Hill, TX: What It Costs and How Long It Takes
Asphalt paving in Cedar Hill typically runs $3,500 – $9,000 for a new drive, and a full resurface (mill and overlay) generally lands in the lower half of that range. A standard two-car drive is a 2 – 3 day job: one day of prep and grading, one day of paving, then a short curing window before you park on it. For acreage properties with long service drives out to a detached workshop, expect a longer schedule and a higher number. Call (844) 797-4808 for a free on-site estimate.
From bare ground to a finished drive: how we build it
Asphalt is unforgiving. The blacktop you see is the easy part; almost everything that decides whether the drive lasts 8 years or 25 happens below it. Here’s the sequence we run, and what you’ll be deciding at each step.
Stage 1: Site walk and grade check (day 1, about an hour). We measure the run, check the existing base, and look at how water moves off the property. On Cedar Hill’s hillside lots, that conversation is mostly about slope and where the water goes after a storm. This is also where we flag rock, roots, or a grade change that will need retaining work. You decide the alignment: where the drive enters, where it widens, and whether it turns to reach a shop or garage.
Stage 2: Excavation and subgrade prep (day 1, 4 – 6 hours). We strip the old surface or topsoil, shape the subgrade, and compact it in lifts. On the west side of Cedar Hill near Joe Pool Lake, this is where limestone shows up within a few feet and a rock saw comes out – that adds time and cost, and it’s better to know on day one than day three. East-side lots with mature oaks may need a tree-protection plan before anything gets dug. You approve the base depth and the drainage plan here.
Stage 3: Base and edge restraint (day 2, 3 – 4 hours). Crushed stone base goes down and gets compacted, then edge restraints are set. A heavier base is the single best money you can spend if the drive will carry a truck or a trailer. You choose base thickness based on what will actually be driven on it, not on what looks good in a brochure.
Stage 4: Paving (day 2, 2 – 4 hours). Hot-mix asphalt is laid and rolled while it’s still workable. Compaction is checked as we go. You’ll see the finished surface by end of day, but it isn’t ready to drive on yet.
Stage 5: Cure and seal (3 – 7 days out, then a season later). The drive cures over the next few days. Sealing is typically scheduled 6 – 12 months after installation, once the asphalt has had a chance to set. You decide the seal timeline; we’ll tell you when it’s actually ready, not when it’s convenient to sell you the service.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Resurface or replace? The options you’ll weigh
For most Cedar Hill homeowners, the real choice is between a full new install, a mill-and-overlay resurface, or patching plus seal. Each has a place, and the wrong pick costs you twice.
- Full new asphalt install: tear out, new base, new surface. Best when the base is failing or the drive is 20+ years old. Highest upfront cost, longest service life.
- Mill and overlay (resurfacing): grind off the top layer and lay fresh asphalt over sound base. Cheaper and faster than a full rebuild, but only works if the base underneath is still solid. If the base is gone, you’re paving over a problem.
- Patch and seal: the economical fix for isolated cracks and worn spots. Good for buying a few years, not for fixing structural failure.
- Base thickness: a standard residential drive gets a lighter base than one that carries a heavy truck or a trailer to a workshop. Oversized or heavy doors and long service drives usually justify a heavier base.
- Drainage and slope: on Cedar Hill’s hillside lots, how the drive sheds water matters as much as the asphalt itself. Sometimes a small retaining wall or swale is the right call, and it’s part of a full Driveway & Pavers in Cedar Hill conversation rather than a separate line item.
- Material grade: standard mixes are fine for most drives; heavier-traffic mixes cost more and hold up longer where vehicles and equipment are frequent.
If you’re weighing asphalt against pavers or concrete, our Driveway & Pavers service covers the comparison in full. For this job, we’re talking asphalt only, and we’ll say plainly when asphalt isn’t your best option.
What Asphalt Driveways & Resurfacing costs in Cedar Hill, TX
Most asphalt driveway work in Cedar Hill falls between $3,500 and $9,000, and resurfacing tends to sit below that ceiling. Here’s what actually moves you toward the low or high end:
| Line item | Typical range |
|---|---|
| Asphalt driveway paving (new) | $3,500 – $9,000 |
| Driveway replacement (full tear-out and rebuild) | $5,000 – $14,000 |
| Driveway sealing (after cure) | $250 – $700 |
The variables that push the number:
- Length and width: a long service drive out to a detached shop or oversized garage is the biggest cost driver. Square footage drives everything.
- Existing condition: sound base means a resurface; failed base means a full rebuild.
- Rock and site access: west-side lots that hit limestone, or east-side lots that need tree protection, add excavation time.
- Base depth and drainage: heavier base and any retaining or swale work add cost but extend life.
- Permits and inspection scope: any work touching grade or drainage may pull in a permit.
A written estimate from us includes excavation, base, compaction, paving, edge restraint, and cleanup. It typically does not include rock removal beyond the estimate, landscape repair, or the later seal coat – we’ll say so upfront. Upfront pricing, no surprises: the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Cedar Hill homes specifically do to this job
Cedar Hill is a hilly, tree-covered city, and that shapes this job more than anything else. Lot to lot, the grade drops sharply, so driveway work here is really slope-and-water work with asphalt on top. On the west side near Joe Pool Lake, builders hit limestone within a few feet and bring in rock saws; on east-side lots with mature oaks, a tree-protection plan comes before any excavation. Much of the new construction is custom-home and lot-clearing work, while the older single-family neighborhoods off Belt Line and Wintergreen – mostly 1980s – 2000s homes, plus ranch homes in the original townsite – often need careful slope management and retaining walls because the terrain falls away from the house. The expansive North Texas clay shifts seasonally, so drives crack and heave, and we schedule exterior work in spring or fall when we can; summer work needs heat plans and dust control. We know this terrain well and cover Cedar Hill and the surrounding area, with neighbors in DeSoto, Glenn Heights, Grand Prairie, and Duncanville calling on us too.
Serving Cedar Hill, TX – Our Local Coverage Area
We serve Cedar Hill and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: Asphalt Driveways & Resurfacing in Cedar Hill
A standard two-car drive is 2 – 3 days of work, plus a few days of curing before you park on it. Longer service drives on acreage properties take more time in excavation and paving, and rock or tree-protection work adds days. Call (844) 797-4808 for a schedule based on your lot.
Resurfacing an existing drive in place usually doesn’t require a permit, but any work that changes grade, drainage, or the footprint can. We’ll pull what your project needs and confirm it in the written estimate before work starts.
Yes, if the base is still sound. A mill-and-overlay grinds off the worn top layer and lays fresh asphalt over the intact base, which is faster and less expensive than a full rebuild. If the base has failed, a rebuild is the honest answer and we’ll tell you so.
Resurfacing generally comes in below the $3,500 – $9,000 new-install range, and the exact number depends on drive size, base condition, and site access. Call (844) 797-4808 for an exact quote – estimates are free.
Every job is backed by our 730-Day Done Right Promise: if it’s not done right, we make it right. That guarantee is in writing on every project, and it holds whether it’s a new drive or a resurface.
If a long service drive or a new shop pad is part of a bigger plan, homeowners often pair this with a New Detached ADU in Cedar Hill or a Junior ADU & Interior Conversion in Cedar Hill, and we’ll coordinate the site work so everything lines up.
Get a free on-site estimate for your Cedar Hill asphalt project
Call (844) 797-4808 to schedule a free on-site estimate for your asphalt drive. We’ll walk the lot, check the base and slope, and hand you a written, line-item quote with the finish and drainage plan spelled out. Calls are answered by a live person 24/7, and every project is backed in writing by our 730-Day Done Right Promise, with 0% financing for 18 months and $1,000 off projects over $10,000 available.
Written by the team at Groundwork Construction Co.