Windows & doors
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Atlas Windows & Doors: The Dallas Owner’s Guide
We install and repair Atlas-compatible windows and doors throughout Dallas, and the honest answer on price is this: window replacement typically runs $4,500 – $15,000 installed, with impact window installation at $8,000 – $25,000 for Dallas homes that need wind-borne debris protection. Most failed parts we see – a broken balance, a snapped operator arm, a door roller shot from heat and grit – diagnose and get replaced in a single visit. Groundwork Construction Co. of Dallas is an independent service provider, not affiliated with Atlas.

Owners rarely call about “a part.” They call because a double-hung sash won’t stay up, a casement crank turns but the window won’t open, or a sliding patio door drags hard enough that someone has to hip-check it closed. In Dallas those three complaints cover most of what we see. This page walks through the parts behind those symptoms, which Atlas series they fit, and what a real fix costs before you commit.
Which Atlas Models This Applies To
Atlas has built multiple lines over the years, and the parts are not interchangeable between them. Vinyl new-construction and replacement series use different balance systems, and a part that fits a 2000s-era single-hung won’t fit a newer builder-grade unit. Before you order anything, find the manufacturer label: it’s usually on the top track of the upper sash, on the inside jamb, or stamped on the sash itself. That label gives you the series and a size code. Measure the visible glass, the frame, and the balance length too – labels fade, and measurements don’t lie.
The OEM-versus-aftermarket decision matters more on windows than on almost anything else. Atlas-specific parts – spring-loaded balances, casement operators with the right arm geometry, weatherstrip profiles – are worth sourcing OEM when they exist, because a balance rated for the wrong sash weight will fail again within a season. Aftermarket is a legitimate choice for generic items: sash lock sets, tilt latches, screen frames, sweep seals. We match the part to the unit, not the other way around. Our technicians have up to 12 years of experience reading those labels and cross-referencing part numbers.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Atlas Windows & Doors Is Failing
- The sash won’t stay up or slams down. A worn or broken spiral or block-and-tackle balance. The sash weight and the balance’s rated capacity have to match, or it’ll fail again fast.
- The crank spins freely and the window doesn’t move. The operator arm or worm gear has stripped. Common on casements and awnings that take full afternoon sun – heat degrades the grease and accelerates wear.
- Air leaks or a visible gap at the meeting rail. Failed weatherstrip, a bent meet-rail sash lock, or a frame that’s shifted out of square. This is the one Dallas owners notice on the electric bill.
- The sliding patio door drags or won’t latch. Collapsed rollers, a worn track, or a misaligned strike. Dallas soil movement and summer thermal expansion both contribute here.
- Fogging between the panes. A failed sealed unit – the desiccant is saturated and the seal has broken. No part swap fixes this; the IGU itself gets replaced.
Replacement Cost & What’s Included
Here’s what Dallas homeowners actually pay for Atlas-compatible window and door work, including parts and labor:
- Window replacement (full unit): $4,500 – $15,000 typical project range
- Impact window installation: $8,000 – $25,000, driven by count, size, and whether framing needs modification
- Single part replacement (balance, operator, roller, weatherstrip, lock set): quoted line-by-line before we start
- Failed sealed unit (IGU) replacement: quoted per unit, typically well below a full window replacement
What moves the price up: number of units, size and configuration, impact-rated versus standard glass, and whether the existing opening is square. What doesn’t move it: anything after the quote. The number you see is the number you pay, and every job is covered by our 730-Day Done Right Promise. If it’s not done right, we make it right. Groundwork proudly serves local communities and has been in business since 2014.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely check a few things yourself: verify the label and part number, measure the balance, confirm the sash slides in the track without binding, and clean the rollers and track on a sticking patio door. That’s diagnosis, not repair, and it’s useful. Where DIY goes wrong on Atlas windows is the sealed unit and anything involving the glass. A failed IGU is a pressurized assembly that has to be measured to the millimeter and set correctly or it leaks and fogs again. Casement operators look simple until the arm springs and the sash swings free. And if you’re dealing with anything on an upper floor, working at height on a window is where people get hurt.
The safest move is a free estimate. Call (844) 797-4808 and we’ll tell you what’s actually wrong and what it costs to fix it, whether that’s a single balance or a full replacement.
FAQs
Twenty to thirty years for the frames, but the parts wear faster. In Dallas heat, balances and operators commonly need replacement in the 10-to-15-year range, and door rollers go sooner if the track collects grit. The window itself often outlasts the hardware inside it, so a $200 part can keep a good unit in service for years.
Sometimes. Weatherstrip, locks, tilt latches, rollers, and track hardware are repair-and-replace items. Balances and operators are replaced, not repaired, because the internal spring or gear has failed and there’s no rebuilting it to spec. Sealed units are replaced. Call (844) 797-4808 for a free estimate and we’ll tell you straight which case you’re in.
Most single part replacements finish in one visit. A failed sealed unit typically takes one visit per unit. Full window replacement is a larger project and gets scheduled accordingly. We’ll tell you the timeline before we start, and almost all of our part work is done in a single visit.
We identify your Atlas series from the unit label and measurements, then source either the OEM part matching that series or a quality aftermarket equivalent where OEM isn’t available or isn’t the better option. We don’t guess on fit. If the part doesn’t match your unit, we don’t install it. We also work with KraftMaid, Cambria, and Silestone on other projects, but for your window we stay focused on getting the right part in.
Get Your Atlas Windows Fixed in Dallas
Groundwork Construction Co. of Dallas handles Atlas part sourcing, repair, and full window and door replacement across Dallas and nearby areas. We show up in uniform, background-checked, with upfront pricing and no surprises. Our 730-Day Done Right Promise backs every job – if it’s not done right, we make it right.
Call (844) 797-4808 to schedule your free estimate. Live person answers, 24/7. Ask about our $1,000 off projects over $10,000 and 0% financing for 18 months.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.