Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Dallas Owner’s Guide
Boral fence installation in Dallas typically runs $3,500 to $9,000 installed, depending on linear footage, gate count, and whether you’re replacing panels or the full run. That price covers the material, post setting in our expansive clay soil, and a written workmanship guarantee. There isn’t a standard same-day answer here: most residential runs are one to three days on site, and material lead time is the real variable. We’re an independent service provider, not affiliated with Boral, so we’ll tell you plainly what’s available and what isn’t.

Owners usually call us after a wind event or a slow season of watching a post lean. A panel that racked sideways after a spring storm off the Gulf. A gate that dragged on the concrete pad by August. A corner post that started moving because the ground under it swelled and shrank through one too many wet-dry cycles. Boral’s composite fence systems hold up better than most in North Texas, but the failure is almost never the board itself. It’s the post, the footing, or the hardware that pulled loose first.
Which Boral Models This Applies To
Boral makes fencing under its composite and polymer product lines, and the part that matters most in a Dallas install is the post-and-rail system the panels attach to. Panels aren’t interchangeable across series, and profiles change between generations of the same line, so we identify the system before we quote. The label is usually on the inside face of a rail or stamped on the post cap. If the label is gone, we measure the panel thickness and the rail profile. That combination tells us which series we’re dealing with and whether the current profile will mate with what’s already standing.
The OEM-versus-aftermarket decision matters more on fence than it does on a roof. A matching OEM rail keeps the whole run uniform and is what we recommend when more than two or three panels are damaged. If you’re repairing one isolated section, a quality aftermarket post and hardware set can be a sound choice as long as it meets the same spec, and we’ll say so plainly rather than upselling the full run. Here’s the compatibility gotcha: a post that’s slightly undersized for the panel bracket will hold at first and then wallow out through a Texas summer. The dimension that has to match is the bracket-to-post tolerance, not the post’s nominal size. Get that wrong and you’ll be back on the phone within two years.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Fence Installation Is Failing
- Posts leaning after heavy rain. Dallas’s blackland clay swells when wet and shrinks when it dries, and that seasonal movement is brutal on shallow footings. A post set in a small concrete plug will start to rock within a few seasons, especially on the sunny west side of a yard.
- Panels racking out of square. When a post moves, the panel has nowhere to go, so it pushes out of square and the rail ends start to gap. This is a footing failure showing up as a panel problem.
- Hardware corrosion at the brackets. Galvanized fasteners are the weak link in an outdoor system, and a bracket that’s rusting through will eventually let the rail slip. Look at the brackets before you blame the rail.
- Boards fading unevenly or chalking. Composite systems hold color well here, but a section that faces full afternoon sun will show fade faster than the rest, and heavy chalking usually points to a panel that’s older than the surrounding run.
- Gate sag and drag. A gate that starts scraping its pad is a hinge-and-post problem, not a gate problem, and it’s the most common failure we see on Boral gate assemblies after a few years of daily use.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Dallas, replacing a damaged section of Boral-compatible fence runs within our $3,500 to $9,000 installed range for a typical residential run, and the number moves with linear footage, the number of posts that need resetting, and whether the footing has to be dug out and poured fresh. A single-panel swap with hardware sits at the low end. A full run with new posts in proper footings lands at the high end. We price parts and labor as separate line items in a written quote, so you see what the material costs and what the install costs instead of one blended number that hides the markup.
The range is driven by three things in Dallas specifically: footage, post count and soil conditions, and gate assemblies. Gates are more expensive per foot than a straight run because the framing and hardware are heavier. All workmanship is covered by our 730-Day Done Right Promise, and the material carries the manufacturer’s warranty on top of it.

DIY or Call Us?
You can safely check the visible stuff yourself. Walk the run after a rain and note which posts move when you push on them. Look at the brackets for rust. Open and close the gate and see where it drags. Measure the panel thickness and look for a label on the inside face. None of that will hurt anything and it tells us a lot before we ever get on site.
Where DIY goes wrong is the footing. Digging out a set post, pouring a proper footing in clay soil, and getting the new post plumb and at the right depth for bracket alignment is where most homeowner installs fail within the year. The system is only as good as what’s in the ground. We’d rather reset a post once than have you do it twice. Call (844) 797-4808 and we’ll walk you through it and set a free estimate.
FAQs
How long does a Boral fence last in Dallas? A properly installed Boral composite fence in North Texas typically holds up well beyond a decade, and often two, because the composite resists rot and insects far better than wood. The material usually outlasts the footing, which is why the post install matters more than the board. Call (844) 797-4808 for an exact assessment of your run.
Can a failed section be repaired instead of replaced? Often, yes. A single racked panel or a gate that’s dragging can usually be brought back with new hardware and a post reset rather than a full replacement. It depends on whether the post itself has moved and how many panels are affected. Call (844) 797-4808 and we’ll tell you honestly whether you need a repair or a replacement.
How long does the swap take? A single panel with hardware is typically a one-visit job. A full run with new posts and fresh footings is generally one to three days on site, with curing time between the footing and the panel install. Call (844) 797-4808 for a schedule estimate.
How do you source the Boral part? We identify your series from the label or a set of measurements, then source the matching OEM material or a spec-equivalent aftermarket post and hardware set based on what the repair actually needs. We don’t carry parts on a truck, so lead time is quoted honestly up front. Call (844) 797-4808 to get started.
Whether it’s composite fence, KraftMaid cabinetry, or a Cambria or Silestone countertop elsewhere in the yard, the approach is the same: identify what’s actually failing before we sell you a fix. A Boral fence in Dallas is a long-term system, and the good installs are the ones where the footing got the same attention as the panels. Call (844) 797-4808 for a free estimate and design consult. We answer with a live person around the clock, all technicians are background-checked and arrive in uniform, and every project is covered by our 730-Day Done Right Promise. Financing at 0% for 18 months is available, and projects over $10,000 get $1,000 off.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.