Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CGI Fence Installation: The Dallas Owner’s Guide
We install CGI-compatible fencing for Dallas homeowners at a typical installed cost of $3,500 – $9,000, depending on fence type, linear footage, and site conditions. Quotes are free, pricing is upfront, and every installation falls under our 730-Day Done Right Promise. The most common situation we walk into is a gate that suddenly sags or won’t latch, a post that’s leaning after a wet spring, or a section of fence that’s sagging from clay-shift movement no one noticed until the boards buckled.

Fence failures in Dallas rarely happen all at once. A gate starts scraping the driveway and you assume it’s a hinge. A post rocks slightly in dry weather and you figure it’s nothing. Then the summer heat bakes the soil, one hard rain softens it, and the whole run shifts. Owners often find the real problem weeks after the symptom shows up, which is why it pays to know what you’re actually looking at before you start poking around.
Which CGI Models This Applies To
CGI’s residential fence lines run across several series and configurations, and posts, gates, and panels aren’t interchangeable between them. Before we order anything or send a crew out with parts, we identify the specific CGI model from the original installation paperwork or the imprinted label on the post cap or gate hardware. If the paperwork is gone, we measure post spacing, panel height, rail thickness, and gate frame dimensions on-site to match the right CGI-compatible hardware.
The OEM-versus-quality-aftermarket call depends on how you use the fence. On a gate that opens every day, the hinge and latch hardware feeds the wear, so we spec the exact CGI-fit OEM option. On a long privacy run, rails and pickets are less wear-critical, and a tested aftermarket match can do the job without the OEM cost. If you also have CGI hanging hardware or other fixtures inside the house, we source those too. We also service KraftMaid, Cambria, and Silestone products for Dallas property owners who need a coordinated upgrade alongside the fence work.
The part you don’t want to skip: CGI’s sizing changed across some model years. A post or panel that looks identical to a neighbor’s might not fit yours. We verify the exact model before committing to an order, because a “close enough” fence installation in Dallas doesn’t hold up to two summers of soil movement. Our technicians have up to 12 years of experience and will measure before we recommend.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your CGI Fence Installation Is Failing
- Gate sags or drags on the ground. Hinge wear, post lean, or soil movement that pushed the gate post out of plumb. The gate is usually the first thing to show it because it takes the most stress.
- Posts rock or lean after rain. Dallas’s expansive clay soil swells when wet and shrinks when dry. A post set in this soil without the right depth or footing will move seasonally and stay out of plumb.
- Rails pull loose or fasteners back out. Repeated soil movement and temperature swings work the fasteners loose. A single reinstalled screw patch won’t fix a loose rail that’s been wallowing.
- Post bases show rust or rot. If the fence was set with insufficient galvanizing or untreated post feet, the ground-contact zone fails quietly from the bottom up. By the time you see it, the post is already compromised.
- Fence line bows or gaps open between panels. The posts have shifted or the panels were racked. Bowing usually traces back to post spacing and footing, not to the pickets themselves.
Replacement Cost & What’s Included
Full CGI-compatible fence installation in Dallas runs $3,500 – $9,000 installed, and every quote is written line-item: materials, tear-out, post setting, gates, hardware, and permits where they apply. The range moves with linear footage, fence type, and site prep – a short aluminum run versus a long privacy line, for example. We pull the right Dallas permits where required and get them inspected before closing out.
What drives it higher: hard clay digging, gate prep on a slope, or a run that needs posts reset to code depth. What drives it lower: a clean, level lot and a simple gate configuration. We present the number before work starts and hold to it. If other parts of the property are on your list, we also handle windows, roofing, and driveways, keeping you with a single contractor from foundation to finish line. No-hassle upfront pricing with 0% financing for 18 months and $1,000 off projects over $10,000 apply here.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
An owner can safely check a few things before calling: look for a visible model label or original paperwork, measure post spacing and panel height, and note whether the gate rubs on the ground or the post leans. Those details help us quote accurately.
Where it goes wrong: setting or resetting posts in Dallas clay to proper depth and footing, matching CGI-specific panel and gate dimensions, and getting the gate alignment and hardware torque right. A fence that rocks in the wrong season won’t stay up, and a gate installed off-square binds within a month. It’s worth a trained hand on this one. Call (844) 797-4808 and we’ll schedule a free estimate; calls are answered by a live person, 24/7.
FAQs
A properly installed CGI fence in Dallas generally holds up 10 to 20 years depending on material, maintenance, and how well the posts are set in the local clay. Weather and soil movement are the biggest factors; a post set correctly at depth is the single largest lifespan lever. Call (844) 797-4808 for an exact quote – estimates are free.
Sometimes. A sagging gate or a single leaning post can often be repaired if the surrounding posts are sound and the panel isn’t racked. A run with multiple out-of-plumb posts in Dallas clay usually needs broader replacement, and we’ll tell you which before quoting. Call (844) 797-4808 and we’ll assess it on a free estimate.
A typical residential run is completed in one to three days, with larger or slope-heavy properties running longer. Most jobs are finished in a single visit once materials are on site. Call (844) 797-4808 for a timeline on your specific fence.
We source CGI-compatible parts to your specific model and series, using OEM hardware on wear-critical gates and tested aftermarket equivalents elsewhere. We don’t carry stock in a truck, so the right part is ordered to your model and verified before install. Call (844) 797-4808 to start with a free estimate.
Get Your CGI Fence Installation Priced Today
Groundwork Construction Co. of Dallas is an independent service provider and is not affiliated with CGI. We install CGI-compatible fencing for Dallas homeowners backed by our 730-Day Done Right Promise, upfront pricing with no surprises, and background-checked technicians on every job. Financing at 0% for 18 months and $1,000 off projects over $10,000 are available. Call (844) 797-4808 to schedule your free estimate. Live person, 24/7 – no voicemail, no delays.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.