Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
IKO Bathroom Remodeling: The Dallas Owner’s Guide
Bathroom remodeling that involves IKO products – whether that’s IKO waterproofing membrane under your tile, an IKO shower system, or IKO-backed underlayment beneath a wet-area floor – typically runs $9,000 to $28,000 installed in Dallas, depending on scope, fixture count, and how much substrate repair the job uncovers. We don’t do same-day remodels; a real bathroom rebuild takes planning, permits, and a sequenced install, and anyone promising to wrap one in a day is cutting corners you’ll pay for later.

Owners usually find a problem the slow way: a soft spot near the shower curb, grout that won’t stay sealed no matter how many times it’s patched, a faint musty smell that returns every summer, or a hairline crack creeping across the floor tile. By the time the visible symptom shows up in a Dallas bathroom, the waterproofing layer underneath has usually been compromised for months. That’s the moment the call happens, and it’s the right one.
Which IKO Models This Applies To
IKO is best known for roofing, but their waterproofing and membrane lines show up in a lot of Dallas bathroom builds – particularly under tile showers, around wet walls, and beneath floor assemblies in slab-on-grade homes where moisture migration is a real concern. The exact product matters less than the installation system it belongs to: membrane type, thickness, seam overlap, and the drain and curb compatibility all have to line up. If you’ve got a partial roll or a labeled box, the product code and roll width printed on the core or the packaging tells you what you’re working with. If there’s no label, we measure membrane thickness and inspect the seam pattern – that’s usually enough to identify the family and match a compatible replacement.
On the OEM-versus-aftermarket question, our position is straightforward: for waterproofing membranes, match the system. Mixing a generic membrane with an IKO drain flange or curb often voids the assembly’s warranty and creates a seam that fails at the worst possible time – behind finished tile. For flashings, sealants, and general bath accessories, quality aftermarket equivalents are fine and often cost less. We’re an independent contractor and not affiliated with IKO, so we’ll tell you honestly when OEM matters and when it doesn’t. We also handle other premium lines across baths and kitchens – KraftMaid, Cambria, and Silestone among them – when the project scope pulls them in.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your IKO Bathroom Remodeling Is Failing
- Recurring musty odor after showers. This usually means moisture is trapped behind tile or under the floor, and the membrane below has lost its seal at a seam or penetration. Airflow won’t fix it; the source has to be opened up.
- Grout that crumbles or darkens within weeks of sealing. Movement in the substrate or moisture wicking up through a failed waterproofing layer is the cause. In Dallas’s expansive clay soils, slab movement accelerates this, and cosmetic regrouting just delays the inevitable.
- Soft or spongy floor near the tub or shower. Water has reached the subfloor. This is the point where a small repair becomes a rebuild if you wait much longer.
- Tile lifting, tenting, or hollow-sounding when tapped. Bond failure driven by moisture behind the tile assembly. That membrane underneath is either compromised or was never installed correctly to begin with.
- Staining or efflorescence on adjacent walls or baseboards. Water is migrating laterally out of the wet zone. This is the one that surprises Dallas owners most, because the bathroom looks fine inside.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full bathroom remodel in Dallas with proper waterproofing, expect $9,000 to $28,000. The range is driven by square footage, tile selection, fixture grade, and – most importantly – what’s under the surface when we open it up. A contained shower membrane replacement with re-tile typically lands lower in that band; a full gut with new shower pan, waterproofing system, tile, vanity, and fixtures pushes toward the top. We quote line-item, in writing, and the number you see is the number you pay – no mid-job surprises. Every job carries our 730-Day Done Right Promise, so if the waterproofing or tile work fails inside two years, we make it right. Financing at 0% for 18 months is available, and projects over $10,000 get $1,000 off.

DIY or Call Us?
An owner can safely check for the obvious: run the shower for ten minutes and watch for damp spots on adjacent walls, press on floor tile near the curb for movement, and look at the caulk line where the shower meets the floor. Beyond that, this is not a DIY-friendly job. Waterproofing membrane installation requires correct seam overlap, proper drain integration, and a flood test before tile goes down – skip any of those and you’ll be tearing it out within a year. We’ve seen more Dallas bathrooms ruined by a homeowner’s well-intentioned membrane patch than by the original failure. Our technicians have up to 12 years of experience, arrive background-checked and uniformed, and calls are answered by a live person 24/7. Call (844) 797-4808 for a free estimate – we’ll walk the bathroom with you and tell you straight what’s actually failing.
FAQs
A correctly installed membrane assembly should last 20 to 30 years under normal use. Dallas heat and humidity stress the seams, and slab movement is the real wildcard – a good install handles it, a rushed one fails in three to five years. Call (844) 797-4808 to have yours assessed.
Sometimes, if the failure is isolated to a small seam or a single drain penetration and the surrounding membrane passes a flood test. Behind finished tile, though, pinpointing the leak means opening it anyway, and at that point a full replacement is usually the honest recommendation. Call (844) 797-4808 for an in-person call.
A shower membrane replacement with re-tile typically runs four to seven days, including the flood test and cure times. A full bathroom remodel runs two to four weeks depending on scope and permit timelines. We’ll give you a written schedule up front. Call (844) 797-4808 for a free design consult.
We identify your existing product from the label, roll core, or on-site measurement, then order the compatible OEM membrane or system component – not a generic substitute that voids the assembly. We don’t stock parts on a truck; each job is ordered to spec. Call (844) 797-4808 with a photo of the label and we’ll confirm the match.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.