Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
IKO Fence Installation: The Dallas Owner’s Guide
We install IKO fence systems for Dallas homeowners, and most full fence installs run $3,500 – $9,000 installed, depending on linear footage, height and gate count. Most jobs are completed in a single visit once materials are on site, and every install carries our 730-Day Done Right Promise. We’re an independent provider, not affiliated with IKO, but we know the line well.

Owners usually find out something is wrong the same way: a gate that won’t latch in July, posts that wobble after a spring storm, or boards that have gone gray and brittle two summers in. In Dallas, the combination of clay soil movement and 100-degree stretches does more damage to a fence line than almost anything else, and the failure shows up at the posts and fasteners first.
Key Takeaways
- Typical installed price in Dallas: $3,500 – $9,000, quoted upfront with no change orders.
- Post setting and fastener choice matter more in Dallas clay than the panel itself.
- We source IKO-compatible components per job; we don’t claim stock on hand.
- All workmanship covered by the 730-Day Done Right Promise.
Which IKO Models This Applies To
IKO’s fence line covers several material families, and matching the right component means reading the label on the existing post, gate hardware or panel edge rather than guessing. If the original install paperwork is gone, we measure post spacing (commonly 8 feet on center for most residential runs, though gate posts often sit closer), board height and rail thickness, then cross-check against what IKO specifies for that series. Getting this wrong is the most common reason a DIY swap fails: a rail that’s a quarter-inch off won’t seat cleanly in an existing bracket.
On the OEM-versus-aftermarket question, it usually comes down to what’s available and what’s structurally critical. OEM IKO components are the safest match for gate hardware and post caps where fit is precise. For pickets, rails and fasteners, a quality equivalent from a trusted mill performs the same in Dallas heat as long as the species, treatment and dimension match. We tell homeowners plainly which parts must be OEM and which don’t. Our technicians have up to 12 years of experience matching components to existing fence lines, so the recommendation is specific, not generic.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your IKO Fence Installation Is Failing
- Posts that rock when you push them. Dallas clay expands and contracts hard between wet springs and dry summers, and a post set too shallow or in unamended soil will loosen within a few seasons. If it moves now, it will lean worse after the next rain cycle.
- Rust streaks at fasteners and brackets. Standard galvanized hardware corrodes faster in North Texas humidity than most homeowners expect. Once rust reaches the screw shank, the board can pull free in wind.
- Gates that drag or won’t latch. This almost always traces to a post that has shifted, not the hinge. A sagging gate is the earliest visible sign the line is out of plumb.
- Gray, splintering or cupped boards. UV exposure in Dallas is intense, and untreated or under-treated wood breaks down faster here than in cooler markets. Cupping means moisture is getting in from the wrong side.
- Loose or missing pickets after a storm. If a single storm dislodged multiple pickets, the underlying rails or fasteners are already compromised. A patch job hides it for one season.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For a full IKO fence installation in Dallas, the range is $3,500 – $9,000. Small repairs, like replacing a handful of posts or resetting a gate, typically land well under the low end. The range is driven by linear footage, fence height, gate count, material choice, and how much site prep the post line needs. Old fence tear-out and haul-away adds to the total.
Here’s how the pricing breaks down, so there’s no mystery:
- Materials: posts, rails, pickets, fasteners, gate hardware, and any OEM IKO components required for fit.
- Labor: tear-out, post-hole digging, concrete setting, assembly and gate hanging.
- Permits: pulled where the City of Dallas requires them, and we handle the inspection.
You get an upfront, line-item quote and the number you see is the number you pay. Every install is backed by our 730-Day Done Right Promise, and projects over $10,000 qualify for our $1,000 off promotion, with 0% financing for 18 months available.

DIY or Call Us?
There’s real value in what a homeowner can safely check on their own: walk the line and push each post, inspect fasteners for rust, measure gate sag, and note which boards are cupping or loose. That information makes a quote faster and more accurate.
Where DIY goes wrong is post replacement and gate re-hanging. A post that isn’t set deep enough in Dallas clay will fail again within a couple of seasons, and resetting a gate onto a shifted post without correcting the post itself just moves the problem. If your post line is moving or a gate is unsafe to operate, call us rather than spending a weekend on a fix that won’t hold.
Call (844) 797-4808 for a free estimate. We’re happy to look at photos or come out and tell you honestly whether you’re looking at a repair or a full install.
FAQs
A properly set IKO fence in Dallas typically lasts 12 – 20 years, with post integrity being the deciding factor. Clay soil movement and UV exposure are the two biggest variables. If posts are set correctly and fasteners are corrosion-resistant, the panels will outlast most homeowners’ expectations.
Yes, if the failure is isolated to a few posts, boards or a gate, repair is usually the right call and far cheaper. Once multiple posts are loose or the line is out of plumb across a long run, replacement is the better value. We’ll tell you which you’re facing after a quick assessment.
Most residential installs are completed in a single visit, with larger runs or complex gate work sometimes extending into a second day. We confirm timing in the quote so you know what to plan for. Call (844) 797-4808 to schedule your free estimate.
We identify the correct series from labels, measurements or existing hardware, then source OEM IKO parts where fit is critical and quality equivalents where it isn’t. We don’t claim to keep parts on hand or carried on a truck; each job is sourced specifically. Our technicians have up to 12 years of experience matching components to existing lines.
If you’re weighing a repair against a replacement, or you already know the line needs work, call (844) 797-4808 for a free estimate. We answer live, 24/7, and our quote is upfront with no surprises. We also serve homeowners across our other trade lines, including KraftMaid, Cambria and Silestone projects, all under the same 730-Day Done Right Promise.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.