Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Fence Installation: The Dallas Owner’s Guide
Jerith aluminum ornamental fence installation in Dallas typically runs $3,500 – $9,000 installed, depending on linear footage, height (4 ft, 5 ft, or 6 ft), grade changes, and gate count. Most single-run residential jobs are completed in one to two days once materials are on site. Groundwork Construction Co. of Dallas is an independent installer, not affiliated with Jerith, and we work with genuine Jerith components and matching aftermarket parts sourced to your model’s specs.

Owners usually find the problem the same way: a gate that suddenly drags on the driveway, a post that wobbles after a spring storm, or a panel section that rattles loose at the bottom rail. In Dallas, our expansive clay soil moves with every wet-dry cycle, so footing and post-set failures show up here that you won’t see in sandier markets. If your fence is leaning, sagging, or rattling, call (844) 797-4808 for a free estimate.
Key Takeaways
- Installed Jerith aluminum fence in Dallas: $3,500 – $9,000, gates and grade work included.
- Jerith models are matched by post size, rail spacing, and picket profile, not by fence height alone.
- Most failures trace back to footing depth and soil movement, not the aluminum itself.
- Work is covered by our 730-Day Done Right Promise.
Which Jerith Models This Applies To
Jerith makes aluminum ornamental fence in several residential lines, and the parts are not interchangeable across them. The three specs that decide compatibility are post size (commonly 2 in. or 2.5 in. square), rail spacing and picket spacing, and picket profile (flat, spear-top, or pressed-point). A 5 ft section from one line will not bolt up cleanly to a 4 ft post from another without adapters, and forcing it is how you get a gate that binds six months later.
On an existing fence, look for the manufacturer label inside a post cap or stamped on a hinge bracket. If the label is gone, we measure the post, the rail-to-rail distance, and the picket center spacing on site. Jerith’s own replacement parts are the safe match when the fence is under warranty or when the profile is discontinued; quality aftermarket equivalents in the same gauge and finish cost less and perform the same on out-of-warranty runs. We’ll tell you which route makes sense for your fence, not ours. We also source KraftMaid, Cambria, and Silestone products for other trades.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Jerith Fence Installation Is Failing
- A gate that drags or won’t latch. Usually a settled post or a worn hinge and self-closing spring, not a bent gate frame. Dallas soil shifts enough that a post set too shallow will move within a season or two.
- Leaning or wobbling posts. Footings that were poured too shallow or without proper concrete depth give way as the clay expands and contracts. This is the most common failure we see on Dallas fences.
- Loose or rattling panels. Usually a failed bottom rail bracket or a picket that’s worked free of its rail channel. Catch it early and it’s a part swap; ignore it and the section racks out of square.
- Rust or finish failure at welds and cut ends. Jerith’s powder coat holds up well, but any field-cut or drilled point that wasn’t touched up will corrode faster in humid North Texas summers.
- Rack and twist along a slope. A fence installed level instead of racked to follow the grade puts constant stress on brackets and hinges, and parts fail in a predictable line from the low end up.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed Jerith aluminum fence installation in Dallas runs $3,500 – $9,000. The range moves with linear footage, fence height, how many gates, slope and grade work, and whether old fence and footings need removal. Here’s what drives the number:
- Posts and footings: proper depth-set concrete footings, the single biggest factor in how long the fence lasts.
- Panels and pickets: matched to your model’s post size and profile.
- Gates and hardware: hinges, latches, and self-closing springs.
- Labor and cleanup: including hauling off the old fence where needed.
You get a written line-item quote up front. The number you see is the number you pay, and all work is covered by our 730-Day Done Right Promise.

DIY or Call Us?
You can safely check a few things yourself: measure the post and rail spacing so you know your model line, confirm the gate hardware is snug, and look for the manufacturer label inside a post cap. What goes wrong for homeowners is the footing work. Digging out and re-pouring a post at the right depth, racking a panel to a slope correctly, and getting a gate to swing true are where the job turns into a call anyway. Aluminum fence parts aren’t dangerous like garage door springs, but a post that isn’t set right leaves you with the same sagging gate next spring. If the footing or gate’s the issue, let us handle it. Call (844) 797-4808 for a free estimate.
FAQs
A properly installed Jerith aluminum fence typically lasts 20-plus years in Dallas, with the powder coat holding up against sun and humidity. The footings are what fail first, often within 3 to 5 years if they were set too shallow for our clay soil. Call (844) 797-4808 for an exact quote – estimates are free.
Often yes. A loose panel, a hinge, a single post, or a gate spring can usually be swapped without touching the rest of the run. We’ll tell you honestly whether a repair or a larger fix makes more sense. Call (844) 797-4808 for a free estimate.
Most single-run residential Jerith fence installs in Dallas finish in one to two days once materials are on site. Larger yards, multiple gates, and heavy grade work add time. Call (844) 797-4808 for a free estimate.
We match the part to your model by post size, rail spacing, and picket profile, using genuine Jerith components or a quality aftermarket equivalent in the same gauge and finish. You’ll know which one we’re using and why before we order. Call (844) 797-4808 for a free estimate.
Ready to get your Jerith fence straightened out? Call Groundwork Construction Co. of Dallas at (844) 797-4808 for a free estimate – calls are answered by a live person 24/7, our technicians are background-checked and arrive in uniform, and every job is backed by our 730-Day Done Right Promise. Ask about $1,000 off projects over $10,000 and 0% financing for 18 months.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.