Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Moen Bathroom Remodeling: The Dallas Owner’s Guide
We install Moen-compatible bathroom remodeling in Dallas, with full bathroom remodels typically landing between $9,000 and $28,000 and smaller projects starting around $5,000. Most work begins after a scheduled in-home design consult, not same-day, because a real bathroom rebuild involves permits, fixture matching, and a predictable, written schedule. If you’re like most owners, you found this page after a failing Moen part, whether it’s a leaking Moen 1222 cartridge, a Moentrol handle that won’t hold temperature, or a shower trim that’s loose against the tile. In Dallas’ hard water, those symptoms show up earlier than you’d expect, often inside 5 – 7 years on the original cartridge.

Key Takeaways
- Full Moen bath remodels in Dallas run $9,000 – $28,000; a small bath remodel is $5,000 – $12,000.
- Moen parts aren’t one-size: 1222, 1225, 1200, and 1255 cartridges fit different valve bodies.
- Hard water in North Texas accelerates cartridge wear, scale, and finish pitting.
- We’re an independent contractor, not affiliated with Moen. We match and install compatible parts.
Which Moen Models This Applies To
Moen’s faucet and shower families have overlapping cartridges, which is where most wrong-part purchases happen. The 1222 fits single-handle kitchen and widespread bath faucets (like the Chateau and Monticello lines). The 1225 is a newer, low-lead version of the 1222 with the same footprint but a different sealing profile. The 1200 fits older single-handle bath faucets, and the 1255 fits many two-handle and posi-temp valve bodies from the 1980s and 1990s. Pull the handle and check the stem stamp or the valve body label; if the stamp is worn, take a photo with a ruler next to the cartridge and we’ll match it from there.
On OEM vs aftermarket: Moen’s own cartridges carry a limited lifetime warranty for the original purchaser, which is a real advantage on a full remodel when the fixture is under 10 years old. Aftermarket brass cartridges can run 40 – 60% cheaper but often use softer seals and thinner brass; in Dallas heat cycling they tend to fail a year or two earlier. We source OEM Moen parts as the default. If the budget pushes toward a compatible equivalent, we say so upfront and put it in writing.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Moen Bathroom Remodeling Is Failing
- Dripping from the spout overnight. This is the cartridge seal wearing, usually the O-ring on the 1222/1225. In Dallas hard water, mineral scale cuts seal life short.
- Handle turns hard or squeaks. Internal cartridge friction; on Moentrol valves this often means the balancing spool is sticking.
- Water temperature swings in the shower. Failing pressure-balancing cartridge or a scaled tempering spool. Common in older Dallas homes with mixed plumbing.
- Water pooling at the base of the faucet or behind the trim. Worn cartridge or a failed trim seal. Left alone, this causes subfloor and tile damage.
- Pitted, cloudy finish on the fixture body. Mineral attack on older Moen chrome or brushed nickel; not a cartridge failure, but a good trigger to refresh the trim and valve together.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Here’s the honest picture on Dallas pricing. The ranges below are what you should expect on a written bid, and the number you see is the number you pay; we don’t run change orders on small swaps.
| Scope | Installed Range (Dallas) |
|---|---|
| Full bathroom remodel with Moen fixtures | $9,000 – $28,000 |
| Small bathroom remodel | $5,000 – $12,000 |
| Walk-in shower installation (Moen trim + valve) | $4,500 – $12,000 |
| Tub-to-shower conversion | $3,500 – $10,000 |
| Shower replacement | $3,000 – $8,500 |
| Bathroom vanity installation | $800 – $3,000 |
What drives the range: cartridge and valve replacement (usually $75 – $220 in parts plus 30 – 90 minutes of labor), fixture grade (Moen’s basic vs. higher-end trim can shift the number $400-plus), tile and substrate work, and whether permits are needed for valve relocation or drain changes. All our work is covered by the 730-Day Done Right Promise; if the install isn’t right, we make it right. Parts we source carry the manufacturer’s own warranty, and we hand you the receipts.
DIY or Call Us?
Some things are safe for a careful owner: swapping a Moen 1222 or 1225 cartridge, replacing a shower trim kit, or refreshing a vanity faucet when the shutoff valve works cleanly. Those are low-risk with the water off. What we don’t recommend for a DIY attempt: opening up a wall to replace a shower valve, converting a tub to a shower, or moving plumbing for a vanity relocation. Those touch framing, waterproofing, and the drain line, and a small leak behind tile in a Dallas summer attic heat load can rot a subfloor inside a season. Our technicians have up to 12 years of experience on this exact work, and every crew is background-checked and arrives in uniform. If you’re unsure whether your issue is a part or a valve, call (844) 797-4808 and we’ll help you decide. Free estimates, up-front pricing, and 0% financing for 18 months on larger projects are available; that’s $1,000 off on jobs over $10,000.
We also handle KraftMaid cabinetry, Cambria, and Silestone if your Moen bath refresh rolls into kitchen work; one contractor, one schedule, from foundation to finish line.
FAQs
How long does a Moen cartridge last in Dallas?
A Moen 1222 or 1225 cartridge typically lasts 5 – 8 years in Dallas before scale and hard water start causing drips or stiffness. Homes on softened water frequently see 10 – 12 years. Call (844) 797-4808 for an exact replacement quote; estimates are free.
Can a failing Moen part be repaired, or does it need replacement?
Most cartridge leaks can be repaired with a new cartridge (parts + labor usually $120 – $300), but a cracked valve body or badly scaled pressure-balancing spool means the valve needs replacing. Call (844) 797-4808 for an on-site assessment.
How long does the swap take?
A single cartridge replacement is a 30 – 60 minute visit once the correct part is on hand. A trim or handle swap is similar. A valve replacement inside the wall is typically a half day, and a full bathroom remodel with new Moen fixtures runs 2 – 4 weeks depending on tile and permit schedules. Call (844) 797-4808 to schedule.
How do you source the Moen part for my model?
We match your Moen cartridge (1222, 1225, 1200, or 1255) or trim kit to the valve body stamp and model label, then source OEM Moen parts as the default, with compatible equivalents available if the budget calls for it. Call (844) 797-4808 and have your model number or a photo ready; we’ll quote it.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.
Ready to price your Moen bathroom project? Call (844) 797-4808 for a free estimate. A live person answers 24/7, and we’ll walk you through the parts, the timeline, and the upfront number in one call.