A Groundwork company - serving Dallas, TX

Oldcastle Fence Installation in Dallas, TX

FenceFence
Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Oldcastle Fence Installation: The Dallas Owner’s Guide

We install Oldcastle-compatible fencing across Dallas, and installed projects typically run $3,500 to $9,000 depending on height, total linear footage, gate count, and material line. Oldcastle is a manufacturer, not an installer, so matching the right system to your property is the whole job before a single post goes in the ground.

professional roofing service in Dallas, TX

Call (844) 797-4808

Dallas homeowners usually find out something is off the same way: a gate that drags in July heat, a post that rocks in dry clay, or a panel that stopped sitting vertical after the last storm. If you’ve inherited an Oldcastle system or had a fencing line quoted under that name, the details below are for you. We’re an independent installer, not affiliated with Oldcastle, and we say so up front so you know exactly who’s accountable for the work.

Which Oldcastle Models This Applies To

Oldcastle covers a wide catalog, and “Oldcastle fence” on a quote or a box doesn’t tell you which system you actually have. Their residential lines run the usual range: vinyl privacy panel systems, aluminum ornamental and pool-code heights, and steel and composite options sold through building supply yards rather than directly to homeowners. Each line has its own post spacing, panel dimension, and hardware set, and mixing lines is where most failed installs begin.

Identify your system before pricing anything. Look for a manufacturer stamp or label on the inside of a post, the top rail, or under a post cap. If there’s no label, measure a panel’s actual width and height to the quarter inch and note the post profile – round, square, or T-rail. Those two numbers narrow the field fast. On the OEM-versus-aftermarket question, the honest answer is that OEM Oldcastle components fit the first time and aftermarket equivalents usually cost less but vary by a sixteenth of an inch, which matters at the gate and at every post bracket. For a full run, OEM is the safer call. For a single damaged panel or a replacement cap, a measured aftermarket match is reasonable. We don’t stock parts and we don’t carry them on a truck; we spec the correct component against your measurements and source it for the install.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Signs Your Oldcastle Fence Installation Is Failing

Fence problems in Dallas rarely announce themselves. They show up as small inconsistencies you notice walking the dog. Here’s what to look for and what’s actually causing it.

  • Posts that rock or lean after rain. Dallas’s expansive clay soil swells and shrinks with the seasons, and a post set in concrete that’s too shallow or too narrow will work loose within a few wet-dry cycles. Once a post moves, the panel above it carries load it wasn’t designed for.
  • Gates that drag or won’t latch in summer. Heat expansion plus a settling hinge post throws the gate out of square. A dragging gate is usually a foundation problem, not a hinge problem, and adjusting the hinge only buys a few weeks.
  • Loose or backed-out fasteners at panel brackets. Wind load and thermal cycling loosen screws that were driven without pilot holes or into undersized rails. Stainless fasteners last; the wrong screws rust and stain the panel face within a season or two.
  • Panels out of plumb or out of line. A fence run that was never string-lined or was stepped to follow grade without adjusting panel height will read as wavy from the street. It’s cosmetic until it puts stress on posts and brackets, then it isn’t.
  • Fading, chalking, or surface cracking on vinyl. Texas UV is hard on any exterior polymer. Some fading is normal over years, but chalky white residue and hairline surface cracks on a system that isn’t old points to a lower-grade panel, not just weather.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Replacement Cost & What’s Included

For Dallas, a full Oldcastle-compatible fence installation runs $3,500 to $9,000 installed. That range covers materials, posts set in concrete to the correct depth for our soil, hardware, gate build, cleanup, and haul-away. The number you see is the number you pay.

What moves you up or down the range:

  • Linear footage and height. A 6-foot privacy run costs more per foot than a 4-foot line, and footage is the single biggest driver.
  • Gate count and width. Each gate adds hardware, bracing, and alignment time. Double gates and driveway-width openings add more.
  • Material line. Vinyl privacy systems sit lower on the range; aluminum ornamental and composite lines sit higher.
  • Site conditions. Root removal, old fence tear-out, and tight lot lines with limited access all add labor.

Every project is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction, and it’s in writing. Projects over $10,000 qualify for $1,000 off, and 0% financing for 18 months is available. Your estimate and design consult are free.

DIY or Call Us?

Some checks are safe and smart to do yourself. Walk the line and mark any post that rocks by hand. Measure panel widths and heights. Photograph the label or stamp on your hardware. Note where the gate drags. That information makes any installer’s job faster and your quote tighter.

Where DIY goes wrong: setting posts in Dallas clay requires the right depth and the right concrete mix, and a shallow post will pass a wobble test in March and fail by August. Gate alignment is a geometry problem, not a screwdriver problem, and string-lining a long run by eye almost never holds. Panel and rail connection points have torque and fastener specs that get skipped without the right tools. Doing it twice costs more than doing it once. Call us at (844) 797-4808 and we’ll spec it against your measurements and give you a real number, not a guess.

FAQs

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 797-4808
Local Service Coverage

Request a Free Estimate in Dallas

Tell us what you need - Groundwork Construction Co. of Dallas responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch