Bathroom remodeling
Kitchen remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Owens Corning Bathroom Remodeling: The Dallas Owner’s Guide
Owens Corning bathroom remodeling in Dallas ranges from $9,000 to $28,000 installed, depending on the scope you choose and the moisture-control products you build in behind the tile. Most Dallas bathroom projects we quote run one to three weeks from demo to final walkthrough, not a single day, because tile, waterproofing and inspections need real cure time. In this market, owners usually discover an Owens Corning product has failed the same way: a soft spot behind the shower wall, a moisture stain creeping past the cement board, or an insulation batt that’s gone limp and dark after two summers of attic heat. The product itself rarely fails on day one. It fails after years of Texas humidity finding a seam that was never taped right.

Which Owens Corning Models This Applies To
Owens Corning doesn’t make a single “bathroom remodeling” product. What Dallas homeowners actually install from this brand falls into a few categories, and knowing which one you have changes everything about the part you need.
The most common is Owens Corning FOAMULAR rigid foam board, used as a tile backer in wet areas or as insulation behind a bathroom wall. It comes in thicknesses from ½ inch to 2 inches, and the compressive strength rating (labeled as 15, 25, 40 or 60 psi) tells you which grade you’re holding. Bathroom walls typically call for the 25 psi or higher grade; builders who used the 15 psi utility grade in a shower wall are the ones we find failing.
Second is Owens Corning PINK fiberglass batts, still the default insulation in Dallas bathroom exterior walls. R-values for 2×4 walls land at R-13 to R-15; 2×6 walls run R-19 to R-21. If you’re matching a batt, the R-value is printed in large type on the kraft facing, and the width (15 inch or 23 inch) has to match your stud bay exactly, or you’re creating an air gap that defeats the purpose.
Third, and less common in bathrooms but present in older Dallas builds, is Owens Corning basement finishing insulation repurposed in below-grade or slab-adjacent bathroom spaces.
To identify what you have, pull the label off the product itself before you buy anything. The label carries the series, the R-value or compressive strength, and the lot code. Match all three. For the OEM-versus-aftermarket decision: FOAMULAR has real, tested equivalents from other manufacturers that meet the same ASTM C578 standard, and a quality aftermarket board is a legitimate choice when the spec matches. PINK fiberglass batts are less forgiving; aftermarket batts with the same R-value but a lower density will sag faster in a Dallas attic, so stick close to the Owens Corning spec there. One note: Groundwork Construction Co. of Dallas is an independent service provider, not affiliated with Owens Corning.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Owens Corning Bathroom Remodeling Is Failing
- Soft or spongy spots behind the shower tile. Water has reached the foam board or the framing behind it. This is usually a taped-seam failure or a missing waterproofing layer, not the board itself.
- Musty smell that returns after cleaning. Moisture is trapped inside a wall cavity. In Dallas bathrooms without a working exhaust fan, this shows up within two to three years.
- Limp or discolored fiberglass batts in the wall. The kraft facing has been wet, and wet batts lose most of their R-value. You’ll feel the difference as a cold wall in winter.
- Grout cracking along a straight line at the shower floor or wall seam. The backer board has flexed or shifted. That’s a substrate failure, not a grout failure, and re-grouting is a temporary patch.
- Peeling paint or bubbling drywall on the bathroom’s shared wall. Moisture has migrated through the backer assembly into the drywall on the other side. This one is a real warning sign, and it’s worth opening the wall.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Owens Corning-backed bathroom remodel in Dallas runs $9,000 to $28,000, and the range is driven by four things: square footage, whether you move plumbing, the tile and fixtures you select, and how much water damage we find once the wall opens up. A small bathroom remodel lands between $5,000 and $12,000. A walk-in shower installation runs $4,500 to $12,000, and a tub-to-shower conversion comes in at $3,500 to $10,000.
Every scope we quote is line-item, upfront and fixed. That means the board product, the waterproofing membrane, the fasteners and sealant, the tile, the fixtures, the labor and the permit are each shown with a number against them. There’s no open line for “miscellaneous” and no change orders based on assumptions. If the price changes, it’s because you approved a change, not because the crew found something and passed the cost along quietly. All work carries our 730-Day Done Right Promise, so if something fails in the first two years, we make it right.
DIY or Call Us?
You can safely handle a few diagnostic steps. Turn off the water, pull the escutcheon plate off the shower valve and look for moisture behind it. Check the label on any exposed insulation or foam board with your phone camera. Run the exhaust fan and hold a tissue to the grille to confirm it’s actually pulling air. Those three checks tell you most of what you need to know before you call anyone.
Where DIY goes wrong on this one is the wall assembly. Taping foam board seams wrong, skipping the waterproofing membrane, or reinstalling fiberglass batts with a gap at the top plate all create a moisture problem you won’t see for years. The visible tile will look perfect the day you finish and fail on the inside during the third summer. We also run into plenty of Dallas bathrooms where the original install put the vapor barrier on the wrong side of the wall; fixing that means taking the wall down to the studs. It’s not a repair, it’s a rebuild, and it needs to be planned rather than improvised.
If you’re not sure which side of that line you’re on, call (844) 797-4808. A technician can walk you through what you’re looking at before you spend a dime on materials.
FAQs
The board itself should last 50 years or more when it’s installed correctly and kept dry. In Dallas bathrooms, that “kept dry” clause is where things go sideways. The foam board holds up fine; the taped seams, the waterproofing membrane over it, and the sealant at the penetrations are what fail first, and they typically fail in the 10-to-15 year window if the exhaust fan is undersized or run only occasionally. Call (844) 797-4808 for a free assessment and an exact quote.
Sometimes, and it depends entirely on how far the moisture traveled. A single cracked seam behind a shower niche can be cut out and re-taped with a proper waterproofing layer for a few hundred dollars. Once the moisture has reached framing or the drywall on the other side of the wall, the answer is almost always a partial tear-out, and that pushes you toward the lower end of the $5,000 to $12,000 small-bathroom range. We’ll tell you which one you’re looking at before you commit.
A small bathroom remodel runs 7 to 10 working days. A full bathroom remodel runs 14 to 21 working days. The clock is driven by waterproofing cure times and tile set times, not by how fast a crew can move. Anyone promising a full Owens Corning bathroom remodel in Dallas in three days is skipping steps, most likely the waterproofing membrane cure window. Call (844) 797-4808 to schedule your free estimate and design consult.
We source by model and lot match, from verified distributors, not from whatever’s on the shelf. When you book, we ask for a photo of the product label, the R-value or compressive strength rating, and the approximate year the bathroom was built. That lets us order the exact grade and thickness rather than the nearest equivalent, and it saves a trip back to the supply house mid-job. For kitchens we work with KraftMaid, Cambria and Silestone on the same principle. We don’t stock parts and we don’t carry them on a truck; everything is ordered to spec for your project.
Built to last, backed in writing. Every Owens Corning bathroom remodel we take on in Dallas is covered by the 730-Day Done Right Promise, backed by upfront pricing, $1,000 off projects over $10,000, and 0% financing for 18 months. Calls are answered by a live person 24/7, no voicemail, and every technician arrives in uniform and background-checked. Our technicians have up to 12 years of experience.
Call Groundwork Construction Co. of Dallas at (844) 797-4808 to schedule your free estimate. We’ll walk the bathroom, check the product labels, and give you a written line-item quote you can hold us to.
Written by the team at Groundwork Construction Co. of Dallas, serving Dallas and nearby areas.