Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Glenn Heights, TX: What It Costs and What It Takes
A chain link fence in Glenn Heights runs $3500 to $9000 for most residential lots, and a standard perimeter job is usually a two-day build once the layout is set and utility locates are back. That price covers posts set in concrete, framework, chain link mesh, and the gates that come off the property’s actual access points. Call (844) 797-4808 and we’ll come out, walk the lot lines, and put a written number in front of you.
How a Chain Link Fence Goes In Here, Stage by Stage
Chain link is one of the few fence types where the build itself is quick and the decisions around it take the time. Here’s the real sequence we run.
Stage 1: The walk and the layout (day of estimate, 45 to 90 minutes)
We walk the property with you and mark where the fence actually needs to run, which is often not where the old wire or the plat map suggests. On Glenn Heights acreage, this is where a lot of the surprises surface: old fence lines from when the land was pasture, buried pipe, a stock tank edge nobody’s seen in years. You decide right there whether the run pulls in tight around the house and shop or goes all the way to the surveyed line. That one call swings the total by thousands of dollars because it’s the difference between 300 feet and 700 feet of fencing.
Stage 2: Utility locates and permitting (3 to 10 business days)
We call in the locate service for buried lines, and if your run crosses a utility easement or you’re fencing around an existing septic field, the layout gets adjusted before a single post goes in. Glenn Heights requires a permit for most fence construction, and inspection timing depends on the city’s schedule, so we build that wait into the front of the job instead of the middle. You decide the permit path with us; we pull it and stand for the inspection.
Stage 3: Demo and prep (half a day to a full day)
Old wire, T-posts, concrete footings from a previous fence, brush along the line. On infill lots that were farm and ranch land a generation ago, this stage regularly turns up buried concrete, old footers, and scrap that has to come out before the new line can go in. You don’t have to make a decision here, but this is the stage that most often adds a day nobody expected.
Stage 4: Posts, framework, and mesh (one to two days)
Posts go in at 8 to 10 feet on center, set in concrete and brought to grade. Top rail, tension bands, terminal posts at corners and gates. Then the mesh gets stretched and tied. On a 400-foot residential run, a competent crew is done with this stage inside two days. You decide the gauge and coating weight up front, because it can’t be changed after the rolls are cut.
Stage 5: Gates, tension check, walkthrough (two to three hours)
Gate hanging and final tension come last. We walk it with you, check the gate swing and latch, and hand over the paperwork. Our technicians have up to 12 years of experience, and every job is covered by our 730-Day Done Right Promise. If something shifts or sags inside that window, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Chain Link Options You’ll Actually Choose Between
- Gauge of wire. 11.5-gauge is the residential standard and holds up fine for a backyard run. 9-gauge costs meaningfully more and belongs where dogs lean on the fence or kids play against it daily. On a property with a shop and regular equipment traffic, 9-gauge pays for itself.
- Coating: galvanized vs. vinyl-coated. Galvanized is the value pick and the most common choice in Glenn Heights. Vinyl-coated (usually black or green) adds cost but reads less like a chain link fence from the street and holds color in the North Texas sun.
- Height. 4-foot for pet containment, 5-foot for a general backyard, 6-foot for privacy feel and pool code. Some Glenn Heights subdivisions have deed restrictions on height and color, so check before you commit.
- Gate hardware. Walk gates, double drive gates, and cantilevered slide gates for wide equipment access. A cantilever slide gate is the single biggest line-item jump on most acreage jobs and the one most worth planning for before the posts go in.
- Post setting. Concrete-set posts throughout, versus drive-in posts on soft ground. Concrete is standard and what we recommend on blackland clay.
If the fence is part of a full Fence Installation in Glenn Heights plan that also touches a driveway or a shop approach, we scope it as one project so the grading and the posts get planned together.
What Chain Link Fence Costs in Glenn Heights, TX
Our lead range for this job is $3500 to $9000. Here’s what pushes a job toward one end or the other.
| Line item | Typical range |
|---|---|
| 300 to 400 ft residential run, galvanized | $3500 – $6000 |
| 500 to 700 ft run, acreage perimeter | $6000 – $9000 |
| Upgrade to 9-gauge or vinyl-coated | +$600 – $1800 |
| Walk gate | $250 – $500 each |
| Double drive gate | $600 – $1400 |
| Demo of old fence and debris haul-off | $400 – $1200 |
The variables that move the number: total linear footage, how much old fence and buried debris has to come out, wire gauge and coating, gate count and gate type, and whether the line crosses rough ground that needs clearing. Property line disputes or a fence that has to follow a survey rather than a straight run also add labor.
A written estimate from us lists post spacing, gauge, coating, gate hardware, demo, and permit cost as separate lines. What typically isn’t included: land surveying if the line is in question, cutting and removing large trees along the run, and any retaining or grade work. If your run needs a level pad or an approach poured, homeowners often pair this with Concrete Driveways & Concrete Work in Glenn Heights so the gate approach and the fence go in the same week.
See the difference
Before
After
Before
After
Before
AfterWhat Glenn Heights Homes Specifically Do to This Job
Glenn Heights is a small, fast-growing bedroom city on the IH-35E corridor between Dallas and Waxahachie (ZIP 75123), and the housing stock tells you a lot about fence work here. You’ve got older rural-style homes on large tracts sitting next to 2000s-to-2020s brick-veneer subdivisions, which means two very different jobs. On the newer tract lots, fences run tight and square and the main variable is matching the neighboring line and staying inside deed restrictions. On the acreage tracts, runs are long, the corners are rarely where the owner thinks they are, and buried ag debris shows up on nearly every dig.
The other thing that’s specific to this ground: much of the city sits on expansive blackland prairie clay that was farm and ranch land a generation ago. That clay shrinks and swells hard between wet and dry seasons, and it moves fence posts. Posts that were plumb in August can lean by the following spring if the concrete isn’t set deep enough and the soil isn’t graded to drain away from the line. We set deeper on this soil, and we grade the line so water doesn’t pool along the footings.
We cover all of Glenn Heights, along with nearby DeSoto, Lancaster, Cedar Hill, and Duncanville. Our fence installation service is here if you want the broader picture beyond chain link.
Serving Glenn Heights, TX – Our Local Coverage Area
We serve Glenn Heights and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Chain Link Fence in Glenn Heights
Most residential chain link fences in Glenn Heights are a two-day build once permits and locates are done, plus the wait on the front end for the locate and permit. The build itself is fast; the scheduling around it is what stretches the calendar, so plan on two to three weeks from deposit to done for a typical job.
Glenn Heights requires a permit for most fence construction, so plan on pulling one. We handle the permit application and stand for the inspection as part of the job. A fence that goes in without one can create problems when you sell, so it’s worth doing right. Call (844) 797-4808 for a free estimate and we’ll walk through the permit path for your lot.
In most cases, yes. Chain link is a post-and-mesh system, so there’s no plumbing, electrical, or structural work involved, and the disturbance is limited to the post holes and the line itself. The one thing that does need checking is buried utilities and any septic field along the run, which the locate step covers. Call (844) 797-4808 and we’ll map it out on site.
A chain link fence in Glenn Heights typically runs $3500 to $9000, with the low end on a shorter residential run in galvanized and the high end on a long acreage perimeter with gates. Gauge, coating, footage, and gate count are the main levers. Call (844) 797-4808 for an exact quote – estimates are free and we put the numbers in writing.
Every chain link fence we install is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right. That covers workmanship on posts, framework, gates, and tension. Materials carry their manufacturer’s warranty on top of that. Ask for the details when we’re out for the estimate.
Get a Free On-Site Estimate for Your Chain Link Fence
Call (844) 797-4808 and a live person answers, day or night. We’ll set a time to walk your lines in Glenn Heights, mark the run, talk through gauge and gate placement, and leave you with a written, line-item estimate. Upfront pricing, no surprises, and $1,000 off projects over $10,000. We also offer 0% financing for 18 months if you’d rather spread the cost.
Written by the team at Groundwork Construction Co.