Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Dallas, TX: Cost, Timeline, and What Your Property Actually Needs
Metal roofing in Dallas typically runs $15,000 – $40,000 for a full roof, and most residential installs finish in 2 – 5 days once materials land on site. The bigger variable on acreage and large-lot properties is usually the shop or barn standing beside the house, not the house itself. Call (844) 797-4808 for a free on-site estimate, and we’ll price the house and any outbuilding on the same written quote.
How a Metal Roofing Job Runs, Start to Finish
We work in a fixed sequence so you know what happens on day one and what’s still open on day four. Every stage below carries a decision, and we don’t move to the next stage until you’ve signed off on the one in front of you.
- Stage 1: Inspection and measurement (day 1, 2 – 3 hours). We walk the roof, measure every plane, check decking condition, and photograph the attic from underneath. On a detached workshop or oversized garage, we measure that roof separately and note whether it shares a wall with the house. You decide at this point whether the outbuilding is in scope or gets its own quote.
- Stage 2: Written scope and material selection (day 1 – 2). You get a line-item quote: panels, underlayment, fasteners, trim, tear-off, disposal, and any decking repair. This is the stage where you pick panel profile and finish. Upfront pricing means the number on this sheet is the number you pay, short of hidden rot we couldn’t see until tear-off.
- Stage 3: Tear-off and deck prep (day 2 – 3, one to two days). Old shingles come off, decking gets inspected board by board, and any soft or delaminated sheathing gets replaced. We re-nail where the fastening pattern is thin. On a large Dallas roof this is the longest single stage.
- Stage 4: Underlayment and panels (day 3 – 4, one to two days). Synthetic underlayment goes down first, then eave trim, then panels or standing seam, moving upslope. Panel lengths are cut to the roof run, so the fewer splices the better the result.
- Stage 5: Trim, flashing, and final inspection (day 4 – 5, half a day). Ridge cap, gable trim, pipe boots, valley flashings, and a magnet sweep of the yard. We walk the roof with you and hand over the material and workmanship paperwork. Everything we install is covered by our 730-Day Done Right Promise.
Technicians on this crew have up to 12 years of experience, and they’ve worked enough Dallas roofs to know when a 1970s ranch deck is going to surprise us and when it’s solid.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Metal roofing is not one product. The four choices below drive both the price and how the roof holds up under Dallas hail and summer heat.
- Standing seam vs. exposed fastener. Standing seam panels hide the fasteners under a raised rib, expand and contract cleanly, and last longest. Exposed-fastener panels (screw-down) cost considerably less but rely on washers that eventually dry out in Texas sun. Standing seam suits the house; screw-down is a reasonable call on a shop or barn where you want coverage without a premium price.
- Panel material: steel vs. aluminum. Galvalume or painted steel is the standard for Dallas and holds up well. Aluminum costs more but resists rust better in humid conditions.
- Finish and color. A painted finish with a real warranty against fading and chalk matters more here than in a mild climate. Dark colors on a low-slope roof will bake the attic, so we pair them with proper ventilation.
- Insulation under the panels. A radiant barrier or a ventilated air gap between the deck and the metal cuts summer heat gain noticeably. On a detached workshop where you’ll be working in July, it’s worth every dollar.
If the same property is getting new windows at the same time, homeowners often pair this with Window Replacement in Dallas to finish the envelope in one pass.
What Metal Roofing Costs in Dallas, TX
Expect $15,000 – $40,000 for a full residential metal roof in Dallas, and add $4,000 – $12,000 if a detached shop or oversized garage is in scope. The five variables that push a job to either end:
- Roof size and pitch. A 1,800 sq ft ranch sits near the bottom. A steep, cut-up roof with dormers and multiple valleys sits near the top.
- Decking condition. Replacing 20 sheets of sheathing is a real line item. We don’t know until tear-off.
- Panel system. Standing seam adds a meaningful premium over exposed fastener.
- Flashing complexity. Chimneys, skylights, and roof-to-wall transitions multiply labor.
- Permit and inspection scope. Dallas permitting adds time and cost, and a re-roof that touches structural repairs expands the scope.
Your written estimate includes tear-off, disposal, underlayment, panels, fasteners, trim, and final cleanup. It does not typically include rot repair found after tear-off, gutter replacement, or structural work, and we tell you that upfront rather than after the fact.
See the difference
Before
After
Before
After
Before
AfterWhat Dallas Homes Specifically Do to This Job
Dallas sits on the Blackland Prairie, where expansive clay soil swells and shrinks through the wet-dry cycle. That moves foundations, and a moving foundation moves roof lines. On slab-on-grade ranch homes across Oak Cliff and East Dallas, we regularly find ridge lines out of level and valleys that have shifted a half inch over a decade of dry summers. A metal roof handles that movement better than shingles because the panels flex, but the flashing still has to be built to take it.
Then there’s hail. Spring storms and straight-line winds drive the case for a panel with a proper hail rating and a fastening pattern built for wind uplift. On a large-lot property in the far north or southeast edges of Dallas, the shop or barn roof usually takes the worst of it because it’s the tallest structure on the lot.
Permitting runs through the city, and a re-roof that includes any structural repair will pull an inspection. If you’re also reworking the house, this is worth considering as part of a full Roofing in Dallas project rather than a standalone job.
Serving Dallas, TX – Our Local Coverage Area
We serve Dallas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Dallas
Most residential metal roofs take 2 – 5 days from tear-off to final inspection. A large-lot property with a detached shop can take 4 – 7 days. Call (844) 797-4808 for an exact timeline on your roof.
Yes, a re-roof in Dallas requires a permit, and the scope determines how much inspection you’ll see. If structural repairs are involved, expect an engineered scope. We pull the permits and schedule the inspections.
Almost always, yes. A re-roof sits on top of the existing structure, so nothing inside the house moves. The only exception is when tear-off reveals structural damage that has to be corrected first.
Full residential metal roofing in Dallas runs $15,000 – $40,000. Add $4,000 – $12,000 if a detached shop or garage is included. Call (844) 797-4808 for a written line-item quote; estimates are free.
The installation is backed by our 730-Day Done Right Promise, and the panel manufacturer warranty runs separately on top. If anything we installed isn’t right, we make it right.
Get a Free Metal Roofing Estimate in Dallas
Call (844) 797-4808 and a live person answers any hour. We’ll schedule a free on-site estimate, walk the roof and any outbuilding with you, and hand over a written line-item quote with the materials and scope spelled out. That quote is part of our Roofing service, and it covers Dallas and the surrounding neighborhoods. If impact-rated glass is on your list too, ask about Impact Windows & Doors in Dallas while we’re there.
Written by the team at Groundwork Construction Co.