Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in University Park, TX: What It Takes and What It Costs
An iron fence in University Park, TX typically runs $3,500 – $9,000 for a standard residential run, and most jobs take two to five working days from setting the first post to the final coat of paint. The work is slower here than in most of Dallas because every project is squeezed onto a built-out lot with mature oaks and tight side-yard setbacks. Call (844) 797-4808 for a free on-site estimate and a written, line-item quote.
How We Build an Iron Fence in University Park, Step by Step
An iron fence looks simple until you’re setting posts eleven feet from a live oak that predates the house. Here’s the actual sequence we follow on University Park jobs, and where you’ll be making decisions.
Day 1: Layout and locating. We walk the property line with you and mark every post on the ground with paint or flags, usually 6 to 8 feet on center depending on panel design. Before anything gets dug, the private locating service marks existing utilities. You approve the layout and the gate swing direction this morning, because moving a gate later means resetting posts. On a typical 100-foot front run, layout takes two to three hours.
Day 1 – 2: Digging and setting posts. Posts go into holes 24 to 30 inches deep, set in concrete, with the hole sized about three times the post’s width. This is the part that eats time. On University Park lots with alley backing and mature live oaks, roots will stop a spade on the first hole. We cut around structural roots rather than through them, which sometimes means shifting a post 8 to 12 inches and recutting a panel. You’ll decide at this stage whether you’re anchoring into existing concrete at a driveway apron or setting new footings, and that choice shows up in the price.
Day 2 – 3: Curing and rails. The concrete needs a full 24 hours before load. While it cures, we cut and fit rails and pickets to your layout, including any rake panels that follow a slope. Flat lots are straightforward; lots with fall toward the alley need progressively stepped panels, and each step is custom cut. Gates get built at this stage too, with heavier frame stock and reinforced corners.
Day 3 – 4: Assembly and hang. Panels get set, checked for plumb and line, and welded or mechanically fastened depending on the system you chose. Wrought-iron assemblies are welded on site; aluminum systems typically bolt together. This is a full day on a 6-foot privacy-height iron fence with a walk gate and a drive gate. We hang gates last, adjust hinges, and confirm they latch clean and clear.
Day 4 – 5: Finish and walkthrough. Shop-primed components get touch-up on site at every weld and scratch, then we clean up, haul off debris, and walk the fence with you. Any post that’s out of line, any gate that doesn’t swing right, and any finish blemish gets fixed before we call it done. Nothing gets billed past the written estimate.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between for an Iron Fence
The material decision matters more here than the design decision, because North Texas heat and black-clay soil punish the wrong choice. Here’s how the real options stack up.
- Wrought iron (traditional, welded): The heaviest, most durable option and the one that matches historic Park Cities homes. Genuine wrought iron holds its shape for decades, resists the sway that comes with foundation movement, and takes paint and powder coat cleanly. It’s the top of the price range. If you want a fence that will still be standing when the oaks come down, this is it.
- Aluminum ornamental (bolted or welded panels): The practical pick for most University Park properties. It looks close to iron, weighs less, won’t rust through the coating, and costs meaningfully less. Trade-off: lighter stock flexes more on a long unsupported run, and bolted panels can loosen over years of ground movement. Worth it where budget matters and the run is under 150 feet.
- Steel (mild steel, powder coated): Sits between aluminum and wrought iron on strength and price. Strong and reasonably durable, but bare or thinly finished steel will rust fast in Dallas humidity. Only the right pick if the finish system is genuinely good and touch-up is planned for.
- Post and picket spacing: Standard 4-inch spacing keeps children and pets in. Tighter spacing costs more per panel. If you’re fencing a dog run or a pool, spacing and height get decided together.
- Height and gates: 4-foot decorative, 5-foot security, 6-foot privacy-height iron, and gain the extra drive gate if you have alley access. A custom drive gate on a 12- to 14-foot opening adds real cost but you’ll use it daily.
- Finish: Powder coat is standard and holds up best to North Texas sun. Paint-over-primer is acceptable on wrought iron and easier to touch up locally.
What an Iron Fence Costs in University Park, TX?
Expect $3,500 – $9,000 for a residential iron fence in University Park. That range covers a standard run with one or two gates and a powder-coat finish. The variables that push a job toward the low or high end:
- Linear footage and height: A 60-foot decorative 4-foot run lands near the bottom. A 200-foot, 6-foot fence with a drive gate lands near the top.
- Material grade: Aluminum ornamental at the low end, welded wrought iron at the high end. Steel sits between.
- Existing conditions: A flat, open lot with no roots is faster and cheaper. An oak canopy, alley backing, and existing concrete to tie into add labor.
- Gate configuration: Every gate is custom. A walk gate is modest; a drive gate with heavier frame and hardware can add a meaningful fraction of the total.
- Permit scope: If the fence triggers a permit or HOA review (more on that below), expect the timeline and the paperwork to add cost.
A written estimate from us lists linear footage, material and finish specs, post spacing, every gate and its hardware, and any tree-root or concrete work – so the number you see is the number you pay. Permits, if required, are itemized separately. Call (844) 797-4808 for an exact quote on your property; estimates are free, and everything is backed by our 730-Day Done Right Promise.
See the difference
Before
After
Before
After
Before
AfterWhat University Park Homes Do to an Iron Fence Job
University Park is a built-out, landlocked Park Cities enclave, and that single fact shapes every fence we install here. There’s essentially no vacant land, so we’re always working around a house that’s already there, tight side-yard setbacks, and mature live oaks whose canopies hang over the line. Delivery access and root protection become as decisive as the fence itself. On 50- to 70-foot lots, the alley behind many blocks is often the only practical way to get long rails and panels to the work area.
The housing stock matters too. Many University Park homes are 1920s – 1950s brick and frame cottages, or newer custom builds where an original home was scraped and replaced. On older properties, we’re fitting fence line to foundations that have moved on the area’s expansive black-clay soil, and structural work above grade sometimes needs to be corrected before a post can go in true. The city permitting process and HPISD-driven renovation activity mean fences here are often part of a larger project rather than a stand-alone. If your iron fence is part of a full Fence Installation in University Park, we coordinate the whole run under one schedule. Homeowners often pair this with Patios, Walkways & Pool Decks in University Park when the fence line and a new hardscape are being planned together. We cover the full University Park service area, and every install falls under our Fence Installation service.
Serving University Park, TX – Our Local Coverage Area
We serve University Park and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked About Iron Fence in University Park
Most residential iron fence jobs here take two to five working days. Layout and post setting happen in the first two days, assembly and gates in the next, and finish and walkthrough on the last. Tight lots and heavy root cutting can add a day.
It depends on height, location, and whether the fence sits in a required setback. We check the requirement for your specific property during the estimate and pull any required permits for you. The permit scope is itemized in the written quote.
In most cases, yes. We dig post holes only, cut around structural roots rather than through them, and haul off spoils. Damage to mature oaks is avoidable with planning, which is why layout on day one matters so much here.
Residential iron fence in University Park runs $3,500 – $9,000, with material grade, linear footage, gate count, and site conditions driving the final number. Call (844) 797-4808 for an exact quote; the estimate is free and the written quote holds.
Our workmanship and the iron fence install are covered by the 730-Day Done Right Promise. If something isn’t right, we come back and make it right. Material warranties come from the manufacturer and are provided in writing at the estimate.
Get a Free Iron Fence Estimate in University Park
Call (844) 797-4808 for a free on-site estimate on your iron fence in University Park. A live person answers 24/7, no voicemail. We’ll walk the line with you, measure, talk through material options and gate layout, and hand you a written, line-item quote – usually the same visit. Permits, tree protection, and scheduling get spelled out up front. Ask about our current offers while you’re on the call.
Written by the team at Groundwork Construction Co. of Dallas.