Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Dallas: What It Costs and How Long It Takes
An iron fence in Dallas typically runs $3,500 to $9,000 for a standard residential run, and most jobs are finished in three to five working days from the day we set posts. The work itself is straightforward: layout and utility locate, post holes drilled and set in concrete, panels hung and welded or bolted, then finish coat. Call (844) 797-4808 to schedule a free on-site estimate, and we’ll walk the property line with you and put a written number in your hands.
How We Build an Iron Fence in Dallas, Start to Finish
We don’t treat a fence like a truck-and-a-hammer job. There’s a real sequence, and each stage has a decision that belongs to you.
Stage 1: The walk and the layout (day 1, about an hour)
We meet you at the property line and mark posts with stakes and string. This is where you decide fence height (4-foot, 5-foot, and 6-foot are the common choices, with 6-foot giving real security), the gate locations, and whether the run follows the survey line or pulls in a foot for easier maintenance. If you don’t have a recent survey, now’s the time to find it, because a fence built two feet onto a neighbor’s lot is a problem we can’t weld our way out of.
Stage 2: Utility locate and post holes (day 1 and 2)
We call in the free 811 locate before a single hole gets dug. Once lines are flagged, we drill post holes, typically 2 to 3 feet deep, and set posts in concrete. Spacing is usually 6 to 8 feet on center depending on panel width and wind load. On a 150-foot run that’s roughly 20 to 25 posts, and this is the slow part of the job.
Stage 3: Rails, pickets, and panels (days 2 and 3)
Rails go on first, then pickets, then any welded assemblies. On a welded ornamental fence the sections are often fabricated off-site and dropped in; on a modular system the pickets slot into pre-punched rails. You decide here whether pickets get a spear, a flat cap, or a ball cap, and whether you want a bottom rail for a cleaner look or an open-bottom design that’s easier to trim around.
Stage 4: Gates and hardware (day 3)
Gates are hung and adjusted, hinges set, latch aligned so it catches without a lift. If you’re adding an automatic opener, we rough in the wiring now. Walk-through gates get the most use of any part of a fence, so we spend real time getting the swing and the latch right.
Stage 5: Finish and final walk (days 4 and 5)
Touch-up on any scratched welds, a final coat of paint or powder-coat touch-up, cleanup, and a walk-through with you. You approve the gate swing, the latch, the line, and the post caps before we pull off. Every project carries our 730-Day Done Right Promise: if it isn’t right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between for an Iron Fence
Iron fence is a category, not a single product. The choices below are the ones that actually change how the fence looks, lasts, and costs.
- Wrought iron (true forged): the traditional metal, heavier, and often custom-fabricated by a local shop. It costs the most, looks the best up close, and lasts decades. Suits historic properties and homeowners who want the real thing.
- Steel ornamental: the modern workhorse. Galvanized or powder-coated steel that reads like wrought iron at a lower price. This is what most Dallas homeowners end up with, and it holds up well against our sun and humidity.
- Aluminum ornamental: the lightest and most rust-resistant option, and the easiest to install. It dents more easily than steel, but if you want a durable painted fence without the weight, it’s a solid pick.
- Powder-coat vs. wet paint: powder coat is baked on and lasts longer against UV and humidity; wet paint is easier and cheaper to touch up later. Most homeowners choose powder coat on steel and aluminum.
- Finial and picket style: spear, ball, flat cap, or scroll. This is the aesthetic identity of the fence and doesn’t change the price much, so pick what you’ll actually like looking at for twenty years.
- Gates: walk-through, double-drive, and automated. Each adds cost and each is a separate decision.
What an Iron Fence Costs in Dallas, TX
Our residential range is $3,500 to $9,000, and most Dallas homes land in the middle of that band. What moves the number:
- Linear feet: a 100-foot run and a 250-foot run are different jobs. Length drives post count, panel count, and labor hours more than anything else.
- Material: aluminum sits at the low end, steel ornamental in the middle, and forged wrought iron at the top.
- Gates: a single walk gate is a modest add. A double driveway gate or an automated gate is a real chunk of the budget, and automation needs wiring and a power source.
- Line and terrain: a straight, level run is the easy case. Sloped yards, tight corners, retaining walls, and tree roots across the line all add time and materials.
- Existing fence removal and permits: tearing out and hauling off an old fence is a line item. Where an HOA or the city requires approval, that process adds time.
A written estimate from us is line-item: posts, panels, gates, hardware, concrete, removal, and labor are each listed. The number you see is the number you pay. Nothing gets added after work starts without your signature, and there are no change orders hiding in the fine print.
See the difference
Before
After
Before
After
Before
AfterWhat Dallas Clay and Dallas Lots Do to an Iron Fence
Here’s the local part that other fence pages skip. Dallas sits on Blackland Prairie clay, a soil that swells and shrinks dramatically through the wet-dry cycle. That movement affects fences, but not the way it affects foundations. Posts set in a shrinking clay pocket can heave and lean over a few dry summers, which is why we set them deep and check every hole before it gets concrete. On the other side, our spring straight-line winds and hail beat up anything metal, and powder coat is the finish that survives both with touch-up.
On the ground, Dallas is a mixed bag. Oak Cliff and East Dallas are full of pre-war bungalows where the fence line shares space with older trees and tight side yards. The 1950s-70s slab-on-grade ranch tracts, and the constant infill construction across the city, mean we’re building fences on freshly graded lots and lots that haven’t seen a new fence in decades. Highland Park and University Park bring HOA and historic-district reviews we check before we set a post, and Duncanville and Irving typically bring larger lots where a long iron run pays off. Call (844) 797-4808 and we’ll tell you what applies to your street. If this is one piece of a larger property plan, you’ll often see it alongside Fence Installation or as part of a Fence Installation in Dallas project, and neighbors doing long runs frequently pair it with Patios, Walkways & Pool Decks in Dallas so the whole yard design ties together. We cover all of Dallas, and homeowners building backyard structures often pair this with ADU Design & Permitting in Dallas.
Serving Dallas, TX – Our Local Coverage Area
We serve Dallas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Dallas
Most residential iron fence jobs in Dallas take three to five working days from the day we set posts, assuming utilities are located and materials are on hand. A 120-foot run with one walk gate is typically the four-day case; a larger lot with a double driveway gate runs toward five or six. Call (844) 797-4808 for a timeline based on your lot.
Many residential iron fences in Dallas don’t require a city permit, but some do, especially where the fence sits close to a property line, acts as a corner-lot screen, or the property is in an HOA or historic district. We check the rules for your address before we set a post. Call (844) 797-4808 to confirm what your lot requires.
Yes, in most cases. We drill individual post holes instead of trenching the whole line, so your lawn between posts stays intact. The one spot we may need to clear is the panel access path for the truck and material, and we’ll walk that with you before we start. Call (844) 797-4808 for an on-site look.
Residential iron fence in Dallas typically runs $3,500 to $9,000, with most jobs in the middle of that range. The estimate we give you is the price you pay; anything not listed is not going to show up on a final bill. Call (844) 797-4808 for a free written estimate.
Every fence we install is covered by our 730-Day Done Right Promise: if the workmanship isn’t right, we make it right. That covers the install, the gates, and the hardware we set. Material warranties come from the fence manufacturer and vary by product. Call (844) 797-4808 to talk through coverage for the specific fence you’re considering.
Get a Free Iron Fence Estimate in Dallas
A free on-site estimate is the right first step for an iron fence in Dallas. We’ll walk the property line with you, talk through heights, gates, and finish choices, and hand you a written line-item price. Calls are answered by a live person 24/7, our technicians are background-checked and arrive in uniform, and we don’t leave a voicemail black hole. Call Groundwork Construction Co. of Dallas at (844) 797-4808 to schedule your free estimate.
Written by the team at Groundwork Construction Co. of Dallas.