Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Duncanville, TX: What It Costs and How Long It Takes
A wrought iron fence in Duncanville typically runs $3,500 to $9,000 for most residential lots, and a straightforward run of 100 to 150 linear feet is usually a one to three day job once your panels are fabricated. The big cost lever isn’t the fence itself, it’s the ground: Duncanville’s black clay moves with every wet-dry cycle, so how we set posts here decides whether your iron fence stays plumb or leans within a couple of seasons. Call (844) 797-4808 to set up a free on-site estimate.
How We Build an Iron Fence Here, Stage by Stage
Iron fencing is not a dig-and-drop job. Metal has no flex, so any mistake in the layout or the footings shows up for the life of the fence. This is the sequence we run.
1. On-site measure and layout (day 1, about 2 hours)
We walk the property line with you and mark every post location, gate opening, and corner. This is where you decide the fence height (4 foot, 5 foot, or 6 foot), the panel style, and whether gates swing in or out. We also check the property survey so the fence sits on your side of the line, not the neighbor’s. On acreage or oversized lots the walk takes longer, and we plan the run to reduce the number of posts sitting in soft or filled ground.
2. Utility locate and demo (day 1, 2 to 4 hours)
Texas 811 marks buried lines before anyone digs a shovel. If there’s an old fence, we pull it and haul it off. That step often turns up a surprise: rotted posts, buried concrete from a previous fence, or an old sprinkler line crossing the path. Planning for one trip means we handle these the same day, not a week later.
3. Footings and post setting (day 1 into day 2)
Every post gets a concrete footing, deeper and wider than a wood fence would need, because iron is heavier and the clay here will grab and twist a shallow post. This is also where the schedule depends on the weather. Concrete needs time to cure before you hang steel on it, so we don’t rush it.
4. Panel and gate installation (day 2 to 3)
We set panels, hang the gates, and check every latch, hinge, and clearance. Gate hardware is where cheap installs fall apart first, so we adjust swing, alignment, and self-closing hardware before we call it done. A driveway gate or double gate adds a half day.
5. Final walkthrough (day 3, about 30 minutes)
You walk the line with us. We check plumb, gate operation, and finish, and hand over the care notes for the finish you picked. Any touch-up gets handled before we leave. When something needs attention later, the 730-Day Done Right Promise covers the workmanship: if it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most Duncanville homeowners land on one of these configurations. Each has a real trade-off.
- Wrought iron (solid steel or iron bar): The classic look and the longest lifespan, usually 20+ years with occasional repainting. Heaviest and priciest. Best for front yards and properties where the fence is part of the curb appeal.
- Aluminum ornamental: Lighter, rust-resistant, and lower cost than true wrought iron. Holds up well to North Texas humidity, and powder-coated finishes come in more colors. The right pick on a tighter budget.
- Steel tubing in an ornamental style: A middle ground. Strong enough for security, with a finish that needs attention over time. Good for longer runs where cost per foot matters.
- Height and spacing: 4 foot reads as decorative, 6 foot reads as a barrier. Bar spacing changes the look and, on some lots, whether the fence works for pets or small children.
- Finish: Powder coat holds color longer; a painted finish is easier to touch up but needs recoating every few years.
- Gates: A single walk gate, a double drive gate, or an automatic opener on a wide drive. Automatic gates mean wiring, and on older Duncanville lots that often means a new circuit.
What an Iron Fence Costs in Duncanville, TX
Plan on $3,500 to $9,000 for a residential iron fence in Duncanville. That range covers most standard lots. Five things push a job from the low end to the high end:
- Linear footage: The single biggest driver. A small front-yard run sits near $3,500; a full-perimeter fence on a larger lot climbs toward $9,000.
- Metal grade: Aluminum ornamental runs less per foot than solid wrought iron. Steel tubing falls between them.
- Ground conditions: Clay soil, roots, or an old buried fence means more digging and more concrete. Rocky or filled ground adds labor.
- Gates and automation: Each gate adds cost, and an automatic driveway gate adds wiring and hardware on top.
- Removal and haul-off: Tearing out an existing fence and disposing of it is a line item, not a freebie.
A written estimate from us spells out footage, post spacing, footing depth, gate count, finish, removal, and permit costs, so the number you see is the number you pay. What’s not included unless we list it: landscaping repair after digging, sprinkler line relocation, and any electrical work for an automatic gate. Those get quoted separately before anyone starts. Call (844) 797-4808 for an exact quote, and estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat Duncanville Homes Specifically Do to This Job
Duncanville is a built-out, largely post-war bedroom city in southwest Dallas County, and that shapes iron fence work in ways a new-build suburb doesn’t. Nearly every job here is a renovation on a 1950s to 1970s brick-veneer ranch on a slab, in ZIPs 75116, 75137, and 75138, with scattered 1980s and 90s subdivisions. That means we’re almost always pulling an old fence and tying new posts into ground that’s already been worked. The expansive black clay under this city heaves and shrinks with wet-dry cycles, so a shallow post that would hold fine in sand will lean here within a season. We set footings deep and wide for that reason. The other recurring issue is buried utilities and old sprinkler lines, especially on the older ranch lots, which is why the Texas 811 locate happens before a shovel hits dirt. On lots where a fence shares a line with a patio or a pool deck, homeowners often pair this with Patios, Walkways & Pool Decks in Duncanville so the hardscape and the fence line up in one plan. If you’re adding a structure back by the fence, that’s often planned alongside ADU Design & Permitting in Duncanville.
Serving Duncanville, TX – Our Local Coverage Area
We serve Duncanville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Duncanville
Most iron fences in Duncanville go in over one to three days once the panels are fabricated. Layout and demo happen on day one, footings and posts follow, and panels and gates go up once the concrete has cured. Fabrication lead time on custom panels is the wildcard, so we give you a firm schedule in the written estimate. Call (844) 797-4808 to get your date on the calendar.
Fence permits depend on height and location, so we check the current Duncanville requirements for your lot before we order anything. We handle the paperwork as part of the job rather than handing it to you. Call (844) 797-4808 and we’ll tell you what your specific fence will need.
Usually, yes, with planning. We mark buried lines and sprinkler runs before digging, and work around them where we can. If a line has to be relocated, it gets quoted up front, not discovered mid-job. Call (844) 797-4808 to schedule a walk-through.
Residential iron fence in Duncanville runs $3,500 to $9,000, with footage, metal grade, gate count, and ground conditions driving the number. A written line-item estimate shows exactly what you’re paying for. Call (844) 797-4808 for a free quote.
Yes. Every iron fence we install is covered by the 730-Day Done Right Promise: if the workmanship isn’t right, we make it right. That covers the install, the footings, and the gate hardware. Call (844) 797-4808 with any question about coverage.
Get a Free On-Site Iron Fence Estimate in Duncanville
We’ll come out, measure the run, check the ground and buried lines, and put a written line-item quote in your hands. That’s part of our Fence Installation service, and it’s the same crew that handles Fence Installation in Duncanville across Duncanville and the surrounding area. A live person answers the phone 24/7. Call (844) 797-4808 to book it, and ask about the $1,000 off projects over $10,000 and 0% financing for 18 months.
Written by the team at Groundwork Construction Co.