A Groundwork company - serving Dallas, TX

Jerith Construction Service in Dallas, TX

Kitchen remodelingKitchen remodeling
Bathroom remodelingBathroom remodeling
Home additions & ADUHome additions & ADU
RoofingRoofing
Windows & doorsWindows & doors
Driveway & paversDriveway & pavers
FenceFence
Every visit starts with

Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled

We have financing partners for your dream remodel*On approved credit; ask us about your options
Get your free estimate

Why Dallas Homeowners Choose Jerith Construction

Groundwork Construction Co. of Dallas provides independent service and installation for Jerith aluminum fencing and railing in Dallas, TX. We quote Emperor, Baron and Guardian Series runs weekly, source Jerith-compatible hardware, and install to the manufacturer’s published specs. We’re an independent contractor, not a Jerith dealer, and we’re not authorized by Jerith. What that means for you: no sales quota on a specific series, just a crew that has set enough Jerith posts in Dallas clay to know what fails and why. Call (844) 797-4808 to schedule a free estimate.

professional roofers replacing shingles on a house roof into a dumpster in Dallas, TX

Call (844) 797-4808

Why Trust Groundwork Construction Co. of Dallas for Your Jerith Construction?

Our technicians have up to 12 years of experience, and a good share of that has been spent on Jerith ornamental aluminum. Emperor Series panels have a distinct rail profile and picket spacing. Baron Series is a lighter-gauge panel that behaves differently under wind load. Guardian Series carries the pool-code spacing that has to match Dallas barrier requirements exactly. We know which rail brackets each line takes, how the self-closing hinges are adjusted, and where installers commonly cut corners that show up three summers later.

Parts matter as much as labor. We specify genuine Jerith replacement panels, pickets, rail brackets and hinge hardware wherever they’re still available, because aftermarket brackets that don’t match the racking geometry will open up gaps at the rails within a season. Where a finish or component has been discontinued, we spec a quality powder-coated aluminum equivalent and tell you about the color variance before we order, not after the fence is up.

Every Jerith job we take on is covered by the 730-Day Done Right Promise. If it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space, and it applies to fence and gate installs the same as it does to a roof.

Explore

Styles & brands we work with

  • Kitchen remodeling
  • Bathroom remodeling
  • Home additions & ADU
  • Roofing
  • Windows & doors
  • Driveway & pavers
  • Fence

Common Jerith Construction Problems We Fix in Dallas

Dallas sits in the middle of the Blackland Prairie clay belt, where expansive vertisols swell and shrink through the wet-dry cycle. That soil movement is the root cause behind most of the Jerith problems we get called out for. Here’s what we see most often:

  • Powder-coat chalking and fading on south- and west-facing runs. Dallas UV loads are brutal, and darker Jerith finishes take the hit first. The coating breaks down gradually, going chalky before it fades. It’s cosmetic for a while, then it isn’t – once the film thins enough, the aluminum underneath starts to oxidize at the edges.
  • Post footings that shift or heave in the clay. A post set too shallow in Dallas soil will lift through a dry summer and drop after a wet spring. When one post moves, the whole run racks. Gates stop latching. Panels go visibly out of square.
  • Gate sag and hinge wear on self-closing hardware. Jerith walk gates and double-drive gates ship with self-closing hinges that need adjustment after the concrete cures. Installers who skip that step leave the gate fighting its own spring, and the latch strike drifts out of alignment within months.
  • Racked or bowed panels from field-trimmed pickets. When a panel has to be shortened on site, some installers re-fasten the pickets with generic screws or clips. That kills the panel’s racking strength and the fence starts bowing at the rails. Jerith-compatible rail brackets exist for exactly this reason.
  • Guardian Series pool fencing failing barrier inspection. Pool-code spacing has to be right at the bottom rail and the gate latch height. We’ve re-set more than a few Guardian runs where the original installer eyeballed it, and the fence no longer passes.

Jerith Parts & Our Repair-vs-Replace Approach

We use genuine Jerith replacement panels, pickets, rail brackets and hinge hardware wherever Jerith still supplies them. That keeps the fence’s racking strength and finish match intact. We don’t claim to stock Jerith parts locally – we source them per job based on what your specific run needs. When a finish or component has been discontinued, we spec a quality powder-coated aluminum equivalent and tell you the color variance up front.

On repair versus replace, we’re honest about it. A typical Jerith call starts with a homeowner noticing the walk gate dragging and the latch no longer catching, usually on an Emperor or Baron Series run that’s been in the ground several years. The cause is most often a shifted post footing in clay soil or a hinge set that was never re-adjusted, which racks the panel and throws the gate out of square. That’s a repair. A qualified local pro resets or re-foots the affected post, re-plumbs the gate, replaces worn hinge and latch hardware with Jerith-compatible parts, and re-tensions the run so the self-closing action works again. Isolated damaged panels and single sagging gates stay repairs almost every time. Long runs with badly heaved posts are a different story – there, partial replacement of that section is usually the more honest call, and we’ll say so.

Call (844) 797-4808 if you want a straight read on which way your Jerith fence should go. Estimates are free.

Our Jerith Service Process – Step by Step

  1. 1
    Diagnosis. We walk the run and check every post for heave or lean, test gate self-closing action and latch alignment, and look at the powder coat on sun-facing panels. On Emperor and Baron Series we also check rail brackets for racking movement.
  2. 2
    Scope and quote. You get a written, line-item quote with the parts we’re specifying – genuine Jerith or an equivalent, clearly labeled. Upfront pricing, no surprises. The number you see is the number you pay.
  3. 3
    Repair or install. For repairs, we reset or re-foot the affected posts, re-plumb gates, and swap worn hinge and latch hardware. For new installs, we set posts to depth for Dallas clay, hang gates, and adjust self-closing hardware after the concrete cures – not before. Background-checked technicians, uniformed on every job.
  4. 4
    Test. Every gate gets cycled repeatedly. We check latch strike alignment, self-closing return, panel racking and post plumb before we call it done.
  5. 5
    Warranty. All work is covered by the 730-Day Done Right Promise. If it’s not done right, we make it right.
Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade

Jerith Products We Service & Install in Dallas

We work with the Jerith aluminum lines Dallas homeowners actually have in their yards. Emperor Series ornamental aluminum fencing is the heavier ornamental profile, common on front-yard and perimeter runs. Baron Series aluminum fence panels are lighter-gauge and popular for side and rear yards. Guardian Series aluminum pool-code fencing covers pool barriers where spacing and latch height have to pass inspection. We also service Jerith aluminum walk gates and double-drive gates with self-closing hinges, including hinge and latch replacement, post resets, and re-tensioning. If you’re adding a gate to an existing run, we’ll match the series and finish wherever Jerith still supplies it. We don’t claim to stock any of these – each job is quoted and sourced to what your fence actually needs.

We Also Service These Brands

Jerith is one line we know cold, but it isn’t the only one. Groundwork Construction Co. of Dallas works across a curated set of verified brand partners: KraftMaid cabinetry and Cambria and Silestone countertops for kitchen work, and Kohler fixtures for bathrooms and additions. If your project touches multiple trades – say a garage conversion that needs new fencing and a gate alongside it – that’s a single contractor handling it from foundation to finish line. You’re not coordinating three crews.

FAQs – Jerith Construction Service in Dallas

Service Typical Dallas Range
Aluminum Fence Installation $4,000 – $10,000
Vinyl Fence Installation $3,500 – $9,000
Garage Conversion $30,000 – $80,000

Book Your Jerith Service in Dallas, TX

Whether you need a single sagging gate re-hung or a full Emperor or Baron Series run quoted, Groundwork Construction Co. of Dallas handles Jerith work with upfront pricing and the 730-Day Done Right Promise behind it. Calls are answered by a live person 24/7. Call (844) 797-4808 to schedule your free estimate.

Written by the team at Groundwork Construction Co.

Need Construction help nationwide? Licensed & insured · free written estimates
Call (844) 797-4808
Local Service Coverage

Request a Free Estimate in Dallas

Tell us what you need - Groundwork Construction Co. of Dallas responds fast. No obligation.

By submitting this form you agree to our Privacy Policy and consent to be contacted by phone, email or SMS about your request, including by local professionals who may handle it.

Call Now - 24/7 Dispatch