Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Coppell, TX: What It Takes and What It Costs
An iron fence in Coppell, TX usually runs $3,500 – $9,000 for a typical front or side yard, with most jobs finished in three to five working days once materials land. That covers posts set in concrete, welded or assembled panels, a finish coat, and the gate hardware. If your lot is on acreage with a detached workshop or an oversized drive gate, expect the upper end. Call (844) 797-4808 and we’ll give you a written line-item estimate before anyone touches your property.
How We Build an Iron Fence in Coppell, Start to Finish
Iron fencing is not a one-day job, and anyone who tells you otherwise is skipping steps you’ll pay for later. Here’s the actual sequence we run, with the durations we see on Coppell properties.
Day 1: Layout, locate, and dig
We walk the property line with you and mark post locations at 6 to 8 foot spacing. Before a shovel moves, we call in the utility locate (811) and confirm easements – something that matters more than usual on the larger lots and acreage parcels around Coppell, where irrigation lines and workshop power runs are often buried with no record. Digging and setting posts takes a full day on a standard lot, longer if we’re running a long boundary line.
Day 1 into Day 2: Posts set in concrete
Every post goes into a concrete footing, typically 24 to 30 inches deep and 8 to 10 inches around. On a heavy gate post, we go bigger and deeper – a 10 foot drive gate swinging on a 4 inch post needs real mass behind it. The concrete cures overnight, and that overnight wait is non-negotiable. Setting panels on wet footings is how you get a fence that leans in two years. You’ll decide at this stage whether you want posts on the property line or set back, which affects the final look and how your gate clears the driveway.
Day 2 to Day 3: Setting panels and gates
Once footings are set, the panels go up and we check every run for plumb and level. This is where the fence actually takes shape, and it’s the stage where alignment against an existing brick wall or a slope on a larger lot gets fiddly. We weld or bolt per the system you’ve chosen. You’ll confirm gate swing direction and latch height here – sounds small, but get it wrong and you’ll be annoyed every single day.
Day 3 to Day 4: Gate hardware and finishing
Hinges, latches, and any self-closing hardware get installed and adjusted so the gate swings true and latches clean with one hand. If you’re adding automation for an oversized drive gate, the operator mounts here and we run the safety sensors. Nothing gets left swinging loose.
Day 5: Final walkthrough and touch-up
We walk the whole run with you, touch up finish at any weld or fastener point, and hand over the written warranty. If a permit inspection is required for your project, we coordinate it before we call the job done. You get the 730-Day Done Right Promise in writing – if something we installed fails, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between for Iron Fencing
Not all iron fencing is the same animal, and the choice you make drives both the price and how long the fence survives North Texas summers. Here’s what’s actually on the table.
- Wrought iron (true): Hand-forged or custom-fabricated, welded on site. The heaviest, most customizable option and the most expensive. It suits acreage estates and shop compounds where a drive gate needs to be built to a specific width. The trade-off is cost and a longer lead time on custom pieces.
- Steel ornamental (tubular steel): The practical middle ground for most Coppell homeowners. Panels arrive pre-assembled in standard heights, welded or bolted together. Lighter than wrought iron, holds up well, and costs meaningfully less. This is what most people mean when they say “iron fence” today.
- Aluminum (mentioning only in passing): Lighter and rust-resistant but a different product with its own page. We’re not the ones to sell it to you standing in for iron.
- Finish: powder coat vs. painted: Powder coat holds color and resists chipping better in the heat; a field-painted finish is cheaper and easier to touch up but needs recoating every few years. On blackland clay with hot, dry summers, we generally steer people toward powder coat on anything they want to look good a decade out.
- Post and footing spec: Standard posts versus driven or oversized posts for gates and corner loads. This is where the “done right in one trip” conversation lives – a cheap 8 foot section with shallow footings will lean in clay soil, and you’ll pay twice.
- Gate automation: For acreage properties with an oversized drive gate, an operator with safety sensors is worth the spend. We’ll spec one sized to the gate weight, not one that strains to move it.
What Iron Fence Costs in Coppell, TX
Most iron fence projects in Coppell land between $3,500 and $9,000. That’s a wide range, and five things reliably push a job toward one end or the other.
- Linear feet: The single biggest driver. A 60 foot front-yard run sits at the low end; a 200 foot boundary line on an acreage parcel pushes toward the top.
- Product type: Pre-assembled tubular steel keeps cost down; custom-welded wrought iron climbs quickly, especially with decorative tops and pickets.
- Existing condition: Removing and disposing of an old fence adds to the bill. Rocky or compacted ground slows post digging, and buried irrigation or shop wiring means more careful hand-digging.
- Gates and automation: A single walk gate is small money. A wide drive gate built to swing across a shop apron, with an operator, is where the number jumps.
- Permit scope: A boundary fence within height limits is usually straightforward. On some lots, a taller fence or a gate near a corner sight line needs a permit and inspection, which adds time and a fee.
A written estimate from us itemizes posts, panels, gates, hardware, finish, demo, and permit handling separately – so you can see exactly where the money goes. Things that typically fall outside the base number: landscape repair after digging, hauling off old fencing, and any custom fabrication beyond standard panels. Upfront pricing means the number you sign is the number you pay. For homeowners planning a wider project, iron fencing often folds into a Fence Installation in Coppell plan that covers the whole perimeter at once.
See the difference
Before
After
Before
After
Before
AfterWhat Coppell Homes Specifically Do to This Job
Coppell’s housing stock shapes iron fence work more than most people expect. The city is dominated by meticulous infill builds and tear-down rebuilds in established, high-value neighborhoods like Old Town, plus a steady stream of 1980s through 2000s brick traditional and transitional homes on generous lots. On the older parcels, we often find original boundary fencing that’s been patched a dozen times, and the honest answer is usually to pull it and start clean rather than chase repairs. If your project expands beyond fencing, homeowners often pair this with Patios, Walkways & Pool Decks in Coppell to finish the yard in one pass.
The soil is the other factor. North Texas blackland clay moves with the seasons, which is why footings here need real depth and mass – a shallow-set iron post that would hold fine on sand will tilt in clay within a couple of summers. We catch that at the design stage, not after the fact. New construction in Coppell that touches setbacks or sight lines can also run into city design standards and HOA architectural review, so it pays to confirm those rules before ordering panels. When a project includes a larger structure alongside the fence, such as a detached workshop or a new outbuilding, our ADU Design & Permitting in Coppell work often informs the layout and utility routing.
We cover Coppell and the surrounding ZIP codes 75019 and 75099, and we’re glad to talk through any of this before a proposal – just call (844) 797-4808.
Serving Coppell, TX – Our Local Coverage Area
We serve Coppell and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Coppell
Most residential iron fence jobs in Coppell take three to five working days from start to finish, with concrete footings curing overnight between stages. Larger acreage runs with multiple gates stretch to a week or more. Call (844) 797-4808 for an exact timeline on your property.
Many standard-height boundary fences don’t require a permit, but taller fences, corner-lot sight line situations, and anything in a design-review neighborhood may. We confirm the requirement during the estimate and handle the paperwork if one is needed. Call (844) 797-4808 to talk it through.
In most cases, yes. We hand-dig where irrigation lines or buried wiring run, mark post locations with you in advance, and keep footings clear of established trees and hardscape. Call (844) 797-4808 and we’ll walk the layout with you before we dig.
Iron fencing in Coppell typically runs $3,500 – $9,000, driven by linear feet, product type, gates, and existing condition. Call (844) 797-4808 for a written line-item estimate – estimates are free.
Every iron fence we install is covered by our 730-Day Done Right Promise – if something we built fails, we make it right. That covers workmanship from footings to gate hardware. Call (844) 797-4808 with any warranty question before you book.
Get a Free Iron Fence Estimate in Coppell
Call (844) 797-4808 for a free on-site estimate on your iron fence in Coppell. On that call we’ll ask about your lot, whether you’re fencing a front run or a full acreage boundary, and what gates you need – then we walk the property, confirm the layout, and hand you a written line-item quote with the 730-Day Done Right Promise behind it. A live person answers around the clock. No voicemail, no waiting until Monday.
Written by the team at Groundwork Construction Co.