Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Vanities, Tile & Fixtures in University Park, TX: What It Costs and How Long It Takes
Replacing the vanity, tile, and fixtures in a University Park bathroom usually runs $9,000 – $28,000 and takes two to four weeks from demo to final walkthrough. The number swings most on tile selection, whether the plumbing and electrical get moved, and whether the vanity is a stock cabinet or a custom-built piece. Call (844) 797-4808 for a free on-site estimate with a written line-item quote before anything gets ordered.
How we run a vanities, tile and fixtures job, stage by stage
This is a finish-level job, not a structural gut, so the sequencing matters more than the calendar length. Here’s how a typical University Park project moves.
Stage 1: Site check and mock-up (day 1)
We start by opening the vanity cabinet and looking behind the existing fixtures – shutoffs, the drain stub, the supply lines, and the wall behind the tile. On the older homes in this ZIP, we’re often finding cast-iron drains or no shutoff valve behind the sink at all. That’s the day you learn whether the job is a straight swap or needs a rough-in correction, and it’s the day we confirm your tile and fixture selections so nothing sits on backorder for three weeks.
Stage 2: Demo and substrate prep (days 2 – 3)
Old vanity out, old floor and wall tile down to the substrate, and any water-damaged drywall or backer board removed. If the home has pier-and-beam floors, we check for movement before setting new tile – a floor that flexes will crack a tile job every time, and North Texas clay soils make that a real concern here. This stage is also when we install a new cement backer board or waterproofing membrane. A tile job over the wrong substrate looks fine for a year and then doesn’t.
Stage 3: Rough-in changes (days 3 – 4)
If you’re moving the vanity location, adding a second sink, or relocating the light fixture, this is when the plumbing and electrical get reworked and inspected. This is the stage that can add a day or two and a few hundred dollars. Skipping it because the old layout “worked” is the single most common source of a callback.
Stage 4: Vanity set, tile, and fixtures (days 5 – 10)
Vanity cabinet set and leveled, countertop templated and installed, then floor tile, wall tile, and finally the fixtures – faucets, shower trim if it’s in scope, mirror, lighting, and towel bars. Grout and caulk go last. We schedule the tile setter and the plumber so the fixtures don’t sit in the garage waiting on a completed tile job.
Stage 5: Final walkthrough and punch list (day 10 – 14)
We test every fixture for leaks, check the caulk lines, verify the vanity doors and drawers, and walk through the punch list with you. Anything that doesn’t pass gets corrected before we call the job done. That workmanship is backed in writing under the 730-Day Done Right Promise – if it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The vanity, tile, and fixture options you’ll actually choose between
Most of the budget decisions happen at the selection stage, not on the job site. Here’s what moves the number most.
- Stock vanity vs. custom cabinet. A stock cabinet in a standard size is the cheapest path and works if your layout allows it. A custom-built unit fits an odd-width wall, matches the trim in an older home, and holds up better – but it typically pushes the vanity portion of the budget toward the top of the range. We work with name-brand cabinetry lines so you’re comparing real quality, not just what’s sitting in a warehouse.
- Porcelain vs. natural stone tile. Porcelain is denser, easier to seal, and forgiving of the hard water and heat in North Texas. Natural stone – marble, travertine, slate – reads richer but needs sealing and shows wear faster in a busy household.
- Tile size and layout. Large-format tile means fewer grout lines and a cleaner look, but it’s less forgiving on a floor that isn’t perfectly flat. A smaller tile or mosaic is more accommodating on older slabs and pier-and-beam floors.
- Countertop material. Quartz is the low-maintenance choice – no sealing, consistent color. Marble is beautiful but stains and scratches. Laminate is the value option and holds up if the budget is tight.
- Fixture finish and brand. Faucet and shower trim finishes range from brushed nickel to matte black to brass. Well-known brands cost more but come with a real warranty and replaceable cartridges years later.
What vanities, tile and fixtures cost in University Park, TX
Expect $9,000 – $28,000 for a full vanity, tile and fixture replacement in University Park, with most jobs landing in the $12,000 – $18,000 band. Here’s what pushes a project toward either end.
| Line item | Typical range |
|---|---|
| Vanity cabinet and countertop | $800 – $3,000 |
| Floor and wall tile (labor and material) | $4,000 – $14,000 |
| Fixtures, faucets, and trim | $1,200 – $4,500 |
| Rough-in plumbing and electrical changes | $800 – $3,500 |
| Permit and inspection fees (if required) | Varies by scope |
The variables that push a job to the high end: relocating the vanity or adding a second sink, a slab or pier-and-beam floor that needs leveling, large-format stone tile, a custom cabinet instead of stock, and any water damage found behind the old tile. The low end is a straight swap in the same footprint with porcelain tile and a stock vanity. Every written estimate itemizes labor, materials, and any allowance for selections, so the number you see is the number you pay. If the scope changes after demo, we bring you a change order before anyone swings a hammer – no surprises.
See the difference
Before
After
Before
After
Before
AfterWhat University Park homes specifically do to this job
University Park is a built-out, landlocked Park Cities enclave. There’s essentially no vacant land in 75225, so nearly every project here is a rebuild, a pop-and-add, or a major remodel on a lot that already has a house. That shapes a vanity and tile job in ways it wouldn’t in a newer suburb. You’re working around tight side-yard setbacks and mature live oaks, so staging is tight and protecting the existing trees is part of the job. The housing stock – 1920s to 1950s brick and frame single-family homes, many already scraped for larger new builds – brings pier-and-beam or early slab foundations, and the older cottages often still have original cast-iron plumbing and knob-and-tube-era wiring behind the wall. We correct those during the rough-in stage, sometimes because a fixture swap simply won’t line up with the old stub. The city permitting and inspection process treats two-story additions and rebuilds as routine, so it’s built for this kind of work – but the inspection schedule still drives the calendar, and we pull the permits and pass the inspections rather than leaving it to you. North Texas heat and black-clay soils mean foundation movement is a recurring line item, which is why we check floor flatness before the first tile goes down. Homeowners often pair this with Tile Roofing in University Park or Specialty Roofing in University Park when the same storm season that stresses the foundation has also worked on the roof. When the vanity and tile job is part of a larger scope, it usually fits inside Bathroom Remodeling in University Park, and our Bathroom Remodeling service covers the full range of fixtures and finishes. We work throughout University Park.
Serving University Park, TX – Our Local Coverage Area
We serve University Park and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – Vanities, Tile & Fixtures in University Park
Most jobs take two to four weeks from demo to final walkthrough, with the tile set and fixture install as the longest single stage at five to seven working days. A straight swap in the same footprint can finish closer to two weeks. Call (844) 797-4808 for an exact timeline based on your selections.
Any job that moves plumbing, electrical, or structural elements requires a permit; a finish-level swap in the same location often doesn’t. The city’s permit and inspection process is built for remodels and rebuilds on built-out lots, and we pull the permits and pass inspections when the scope calls for it. We’ll tell you upfront which category your job falls into.
Yes – and that’s the least expensive path. Keeping the vanity in the same location and reusing the existing drain and supply lines keeps you in the lower half of the $9,000 – $28,000 range. Adding a second sink or relocating the vanity pushes you toward the top. Call (844) 797-4808 and we’ll quote both versions so you can compare.
It typically costs $9,000 – $28,000, with the wide spread driven by tile choice, whether the cabinet is stock or custom, and any rough-in work needed behind the wall. Most projects land in the $12,000 – $18,000 band. Call (844) 797-4808 for a free estimate with a written line-item quote.
Every vanity, tile and fixture job is backed by our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space, and it covers our labor, not just the materials.
Get your free estimate
Ready to fix the vanity, tile, and fixtures in a University Park bathroom? Call (844) 797-4808 and a live person answers, any hour. We’ll schedule a free on-site estimate, walk the space with you, and hand you a written line-item quote with fixed pricing and no change orders. Financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off. No voicemail, no waiting until Monday.
Written by the team at Groundwork Construction Co.