Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain link fence installation in Irving, TX typically runs $3,500 to $9,000 for a residential lot, with most standard 4-foot or 6-foot runs landing in the middle of that band. A 150-foot perimeter with two gates and new posts is usually a two-day job. For an exact number on your property, call (844) 797-4808 and we’ll set a free on-site estimate.
Chain Link Fence in Irving: What the Job Actually Involves
Here’s the honest picture. A chain link fence breaks down into four things: posts set in concrete, a top rail, tensioned fabric, and gates. The work is fast compared to most fencing because the material is light and the install is mechanical, not finish work. What separates a fence that lasts 20 years from one that leans in three comes down to three things: post depth, concrete, and how tightly the fabric is stretched.
Irving sits on North Texas black clay, and that soil is the whole ballgame. Clay swells when it’s wet and shrinks when it dries, which is why you’ll see fence lines in the neighborhoods off Story Road leaning and wobbling after a dry summer. Posts set shallow in a 6-inch hole don’t hold. We set them deeper and use bagged concrete, Quikrete or Sakrete depending on what’s on hand, because that’s the difference between a fence and a fence that stays put.
Timeline is simple. Day one is layout, digging, and setting posts in concrete. The concrete cures overnight. Day two is rails, fabric, tension, and gate hang. Most Irving jobs wrap in two working days. Larger properties or rocky dig conditions can push to three.
Key Takeaways:
- Typical Irving chain link fence cost: $3,500 – $9,000
- Standard install window: 2-3 days on-site
- Post depth and concrete quality drive longevity more than fabric brand
- Black-clay soil means post holes need to go deeper than in sandy or loam ground
How We Build a Chain Link Fence: The Five Stages
Stage 1: Site walk and layout. We walk the property line with you, confirm corners, and mark post locations. This is where you decide gate placement and whether you want a walk gate, a drive gate, or both. That decision affects everything downstream, so it happens first. About 30 minutes.
Stage 2: Utility locate and hole digging. Before a shovel hits dirt, we confirm utility locates are clear. In older Irving neighborhoods, gas and water lines can run close to property edges, and hitting one is a bad day for everyone. Once cleared, we dig post holes to depth. Clay is dense work, and this stage often takes the bulk of day one on a 150-foot run.
Stage 3: Setting posts in concrete. Posts go in, concrete goes around them, and we check plumb and height as we go. This is the stage that determines whether your fence stands straight in year ten. The concrete needs to cure before anything gets hung, so we stop here and come back the next morning. You’ll see the posts sitting overnight.
Stage 4: Rails, fabric, and tension. Top rail, tension wire, and fabric get pulled and stretched tight. The tension bar at each end and at every gate post is what keeps the mesh from sagging. We walk the whole run with you before moving to gates so you can see the tension and make sure the height and layout are right.
Stage 5: Gate hang and final walkthrough. Gates get hung, latched, and swing-tested. This is where we confirm clearance, check the latch alignment, and adjust hinges if needed. You walk the fence with us, and anything that needs a tweak gets handled before we leave.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between on a Chain Link Fence
The choices on a chain link job are fewer than on wood or vinyl, but each one moves the price and the lifespan. Here’s what you’re actually deciding:
- Height: 4-foot vs. 6-foot. Four-foot is cheaper and fine for marking property lines. Six-foot is the standard for pet containment and any real privacy or security purpose. The jump adds roughly 15-20% to the material cost.
- Gauge of wire. Chain link fabric comes in 11.5-gauge (standard residential) and heavier gauges for commercial. For a home fence, 11.5-gauge is the right call. Thicker wire costs more and doesn’t add meaningful life on a residential lot.
- Vinyl-coated vs. galvanized. Galvanized is the budget choice and holds up fine. Vinyl-coated in black or green looks cleaner against landscaping and hides the industrial look. It adds roughly 10-15% to material cost and extends the life of the wire.
- Post and rail weight. Standard weight posts are fine for most homes. Heavier posts matter on long runs or if you’re planning to attach anything to the fence later.
- Gate type. A walk gate is simple and cheap. A drive gate for vehicle access doubles or more the gate cost and needs heavier posts to carry the weight over time.
If you’re adding a chain link run as part of a full Fence Installation in Irving project that mixes materials, we’ll spec the posts and gates to match the whole perimeter so you’re not mixing hardware. For properties where the fence ties into grading or drainage work, homeowners often pair this with Concrete Driveways & Concrete Work in Irving to handle the apron and gate approach at the same time.
What a Chain Link Fence Costs in Irving, TX
For a typical residential lot in Irving, a chain link fence lands between $3,500 and $9,000. Here’s how that range breaks down so you can see where your property sits:
| Scope | Typical Range |
|---|---|
| Standard 4-ft perimeter, ~100-150 ft, one gate | $3,500 – $5,500 |
| 6-ft perimeter, ~150 ft, walk gate plus drive gate | $5,500 – $7,500 |
| Large lot, vinyl-coated, multiple gates | $7,500 – $9,000 |
| Gate additions after the fact | Quoted separately |
Four variables push a job toward the high end. Linear footage is the biggest. Gate count and type is second, since each gate needs heavier posts and hardware. Dig conditions matter in Irving specifically, because black clay is harder to dig than sandy ground and can add labor time. Material grade, meaning galvanized vs. vinyl-coated and standard vs. heavier gauge, moves the number modestly. And if the property line runs into an existing concrete pad or retaining wall, that’s demo and disposal work that gets added.
A written estimate from us lists posts, rails, fabric, tension wire, gate hardware, concrete, and labor line by line. What it won’t include unless we scope it: removing an existing fence, hauling off old material, or repairing a property-line issue. We’ll tell you upfront if any of that applies so there are no surprises mid-job. Our Fence Installation service covers the full scope if your project grows beyond chain link.
See the difference
Before
After
Before
After
Before
AfterWhat Irving Homes Specifically Do to This Job
If you’re in South or central Irving, around the old downtown, the Hospital District, or the blocks off Belt Line and Story, you’re probably fencing a 1950s-to-1970s lot. That matters for chain link because those older properties often have property lines that don’t run perfectly square, buried landscape edging, or old fence posts still in the ground that need pulling. Every one of those things adds a step.
The other half of Irving, out toward Las Colinas, Valley Ranch, and the 75063 corridor, is a different job. Subdivision lots from the 1980s through the 2000s are more likely to have a clean line, a prior HOA-approved fence footprint, and possibly an existing fence that just needs replacing rather than a fresh install. If you’re in one of those HOAs, confirm the fence height and color with your association before we order material. Most Irving HOAs that touch fencing will specify height and finish; the install itself is the same, but the approval needs to be in hand before day one.
The clay is the constant. Whether you’re in 75062 or 75063, post depth and concrete are what keep the fence straight through the wet-dry cycle. We handle jobs across Irving and neighboring Farmers Branch, Coppell, Euless, and University Park, and the soil conditions are similar throughout. If your gate approach abuts a driveway that needs resurfacing or replacement, homeowners often pair this with Asphalt Driveways & Resurfacing in Irving so the fence and the drive get finished in the same window.
Serving Irving, TX – Our Local Coverage Area
We serve Irving and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About a Chain Link Fence in Irving
Most chain link fence installs in Irving take two working days on site. Day one is layout, digging, and setting posts in concrete. Day two is rails, fabric, tension, and gates. Larger lots, extra gates, or stubborn clay can stretch it to three days. Call (844) 797-4808 for a timeline specific to your property.
Permit requirements depend on the height, location, and whether your property is in an HOA. Most standard residential chain link runs don’t require a city permit, but we’ll confirm with you before day one. The bigger variable in Irving is HOA approval, which many subdivisions in the Las Colinas and Valley Ranch areas require. Call (844) 797-4808 and we’ll walk through what applies to your address.
Yes, and most installs leave minimal disruption. The only digging is at post locations, which is a series of 8-to-10-inch holes rather than a trench. Grass along the fence line will show some wear where we worked, but it recovers within a few weeks with normal watering. Call (844) 797-4808 if you have specific landscaping concerns and we’ll plan around them.
A residential chain link fence in Irving typically runs $3,500 to $9,000 depending on length, height, gate count, and whether you choose galvanized or vinyl-coated material. A basic 4-foot run on a standard lot sits at the low end; a 6-foot perimeter with a drive gate and vinyl coating lands near the top. Call (844) 797-4808 for an exact quote on your property.
Every fence we install is covered by our 730-Day Done Right Promise, which means if the workmanship isn’t right, we make it right. That covers post setting, gate alignment, and installation quality. Material warranties depend on the fabric and hardware brand, and we’ll spell out what’s covered in writing before work starts. Call (844) 797-4808 with any warranty questions.
Get a Chain Link Fence Estimate in Irving
If you’re ready to price a chain link fence on your property, call (844) 797-4808 and we’ll schedule a free on-site estimate. We’ll walk the line with you, check utility locates, confirm gate placement, and hand you a written line-item quote before you commit to anything. Pricing is upfront, financing is available at 0% for 18 months, and our technicians are background-checked and arrive in uniform. One call gets you a real number for your property.
Written by the team at Groundwork Construction Co.