Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Irving, TX: What It Costs and How Long It Takes
An iron fence in Irving typically runs $3,500 to $9,000 installed, with most residential jobs landing near the middle of that range for 100 to 150 linear feet of ornamental steel or wrought iron at 4 to 5 feet tall. A straightforward property-line run takes two to four working days from demolition to final walkthrough. Call (844) 797-4808 for a free on-site estimate with a written line-item quote.
How an Iron Fence Gets Built Here, Start to Finish
Every job follows the same five stages. Here’s what each one actually involves, how long it takes, and what you’ll be deciding along the way.
Stage 1: Site walk and layout (day 1, about 90 minutes)
We walk the property line with you, confirm where it truly sits, and flag anything buried or overhead: sprinkler mains, gas runs, cable drops, low power lines. On the tight lots common in South Irving, the survey or plat gets pulled out and checked against the physical line, because building to the wrong side of a fence line is the single most expensive mistake in this trade. You decide the fence height and whether the run closes at the back or meets an existing structure.
Stage 2: Permit and HOA paperwork (day 1 to day 5, runs in the background)
Iron fencing above 6 feet, fences on corner lots, and anything in a front or side setback needs a permit in most Irving situations, and Las Colinas and Valley Ranch HOAs have their own style and height rules layered on top. We assemble the drawing, submit, and handle the inspection request. You sign, we file. Nothing gets built until the approval is in hand.
Stage 3: Layout, dig, and set posts (day 2, one full day)
This is the day that determines whether the fence is straight in ten years. Posts go in concrete footings set below the clay’s active zone, spaced on a consistent 6 to 8 foot module, and each one gets checked for plumb and line before the concrete sets. On a sloped yard, we step the panels rather than racking them, which keeps the pickets vertical and the bottom rail evenly off the ground.
Stage 4: Panels, gates, and finish (day 3, one to two days)
Rails and pickets are set, welded or mechanically fastened depending on the system, then the gate hardware and hinges go on and get adjusted. Powder-coated product ships finished, so this stage is assembly, not painting. If you chose a site-applied finish, that’s an extra day. You’ll want to be home for the gate swing test and to confirm latch height.
Stage 5: Walkthrough and final inspection (day 4)
We walk the full run with you, check every gate for a smooth close, confirm post caps and finials are seated, and turn over the warranty paperwork. The city inspection follows, and we meet the inspector on site. You don’t need to be there for that part. Call (844) 797-4808 to start with a site walk.
If the iron run is part of a full Fence Installation in Irving plan that includes a wood privacy section or a driveway gate, we sequence the trades so the iron and the rest go in together instead of tearing up your yard twice.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Iron isn’t one product. What you pick here drives both the number and how the fence looks in fifteen years.
- True wrought iron vs. ornamental steel: Wrought iron is forged and welded, heavier, and repairable by a fabricator; ornamental steel is the more common choice today and costs less for the same look. The trade-off is that steel dents on hard impact where wrought iron bends, but steel holds its powder coat better in North Texas sun.
- Powder-coated vs. site-painted finish: Factory powder coat is baked on and lasts far longer against UV and humidity; site-painted iron gives you a fully custom color but needs touch-ups every few years. Most Irving homeowners pick powder coat in black or bronze.
- Picket spacing and height: 4-foot runs read as decorative boundary; 5 to 6-foot runs with tighter picket spacing do real security work. Tighter spacing costs more per linear foot because it uses more material.
- Rackable vs. stepped panels: Rackable panels follow a slope smoothly; stepped panels hold a horizontal line on grade changes. Sloped lots in older Irving neighborhoods usually look better stepped.
- Gates: A pedestrian gate with a self-closing hinge is standard. A driveway gate is a different scope with its own opener and power run, and we quote it separately.
What Iron Fence Costs in Irving, TX
Expect $3,500 to $9,000 for a residential iron fence in Irving. That’s the installed number, materials and labor included, for a typical 100 to 150 foot run. The variables that push a job toward either end:
- Linear footage and height: A 200-foot perimeter at 6 feet can run past $9,000 on its own. Height and length are the two biggest levers.
- Material grade: Thinner ornamental steel at the low end, heavier gauge or true wrought iron at the high end. The price gap between them is real, and so is the lifespan gap.
- Site conditions: Solid black-clay digging is slower than sandy soil, rock or old concrete footings from a previous fence add labor, and a steep grade means more posts and more cutting.
- Gates and hardware: Each pedestrian gate adds cost; a driveway gate and opener moves the project into a different bracket.
- Permit and HOA scope: Corner lots, setback variances, and HOA design review can add time and fees on top of the fence itself.
A written estimate itemizes footage, post count and spacing, footing depth, gate count, finish, and permit fees. Things that typically aren’t included: removing an old fence (quoted as a separate line), landscaping repair after digging, and any driveway gate automation. Our Fence Installation service handles the broader scope if you’re fencing more than one boundary. Call (844) 797-4808 for an exact quote – estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat Irving Homes Specifically Do to This Job
Irving splits into two very different fence markets, and it changes what we plan for. In South and central Irving around the old downtown and Hospital District, the housing stock is 1950s to 1970s brick-veneer ranches on aging postwar lots, and those lots are where we see the most fence replacement. Original iron and steel runs from that era are often rusted through at the bottom rail where sprinkler overspray and black-clay movement have worked on them for decades. The North Texas clay is the real factor: it swells and shrinks with every wet-dry cycle, and a fence post set too shallow will heave and lean within a few seasons. We set footings deep enough to sit below that active zone, which is the same reason foundation work is a constant line item across this city.
Out in the Las Colinas, Valley Ranch and 75038/75039 corridor, the picture flips. The homes are 1980s to 2000s subdivision product, HOAs are active and specific about fence style and color, and a fence that doesn’t match the approved palette gets flagged. We check the HOA design guidelines before we order material, not after. Whether you’re in 75062 near the old downtown or up in 75039, we cover Irving and the surrounding communities.
Serving Irving, TX – Our Local Coverage Area
We serve Irving and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Iron Fence in Irving
Most iron fence jobs take two to four working days on site, plus one to two weeks for permit approval if one is required. Material lead time on powder-coated panels typically adds one to two weeks before we can start. Call (844) 797-4808 for a timeline based on your actual property.
Often yes, particularly for fences over 6 feet, corner lots, or anything in a front or side setback. We confirm the requirement with the city during the site walk and handle the submittal and inspection if a permit is needed. You won’t be left guessing what’s required.
Yes, in almost every case. We locate buried utilities before digging and route footings around them. If a sprinkler line runs directly under the fence line, that’s a small reroute we quote upfront rather than discover mid-dig.
Plan on $3,500 to $9,000 for a standard residential run, with the final number driven by footage, height, material grade, and gate count. Call (844) 797-4808 for a written line-item estimate – it’s free and there’s no pressure.
Every iron fence we install is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space. Manufacturer finish warranties on powder-coated panels run separately and add to it.
Get a Free Iron Fence Estimate in Irving
Call (844) 797-4808 to schedule a free on-site estimate for iron fence work in Irving. A live person answers, day or night. We’ll walk the line with you, talk through material and height options, and hand you a written line-item quote with upfront pricing – the number you see is the number you pay. If your project also includes hardscape, homeowners often pair this with Patios, Walkways & Pool Decks in Irving, and for larger lot changes, ADU Design & Permitting in Irving often comes up in the same conversation.
Written by the team at Groundwork Construction Co.