Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Aluminum Fence in Dallas, TX: What It Costs and How It Goes In
Aluminum fence installation in Dallas typically runs $4,000 – $10,000, and most residential jobs take two to four days from demo to final walk-through. For a typical lot, that covers layout, posts set in concrete, panels racked to your grade, and gates hung and adjusted. If you’re pricing this against wood or vinyl, aluminum usually lands in the middle and lasts far longer. Call (844) 797-4808 for a free on-site estimate with a written line-item quote.
How We Run an Aluminum Fence Job in Dallas, Start to Finish
Every aluminum fence job follows the same five stages. Here’s the real sequence, how long each stage takes, and where you make the calls.
Stage 1: Walk-through and measurement (day 1)
We walk the property line with you, confirm the exact run, measure gate openings, and identify what’s buried where you want posts. That means calling in locates on gas, water, and any irrigation lines before anyone digs. This is also where you pick fence height (typically 4′, 5′, or 6′), picket spacing, and gate style. Plan on 45 minutes to an hour on site.
Stage 2: Permit and HOA approval (day 1 – 10)
Most Dallas residential fences under 8′ don’t need a building permit, but they do need to respect setback and sight-line rules, and HOAs frequently require an architectural review before the first post goes in. We prepare the submittal package and submit it for you. Approval timelines vary by HOA, so this is often the longest stage. You decide whether to wait for HOA sign-off or hold the job.
Stage 3: Layout and demo of the old fence (day 1 – 2 on site)
We string-line the run, mark post holes at 6′ to 8′ on center, and pull the old fence if there is one. Demo of a standard wood run takes half a day. Any gates, rails, or concrete footings that are still sound can sometimes be reused, and we tell you upfront if that’s worth doing or if it’s cheaper to start fresh.
Stage 4: Posts, panels, and gates (days 2 – 4)
Posts get set in concrete and need a cure window before we hang panels, usually 24 to 48 hours. Then panels go up and get racked to follow your grade, which matters a lot on Dallas lots with any slope. Gates are hung last on their own posts and adjusted for swing and latch. You confirm gate swing direction (in or out, left or right) before we set the posts.
Stage 5: Walk-through and punch list (final day)
We walk the whole fence with you, check every post for plumb, open and close every gate, and correct anything on the punch list before we leave. You get the workmanship warranty in writing, and there’s no final payment until the punch list is signed off.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Aluminum Fence Options You’ll Actually Choose Between
Aluminum isn’t one product. The spec you pick changes both the price and the lifespan.
- Residential vs. industrial grade: Residential panels use thinner wall aluminum and are fine for a backyard. Industrial grade is heavier and holds up better on long runs where wind load is a factor, common out toward the more open acreage lots beyond city center. Expect the industrial spec to add roughly 20 – 30% to the fence cost.
- Powder-coated vs. painted: Powder coat is baked on and holds color far longer than paint. It’s the standard for anything we install and the only finish we’d put on a Dallas fence given the summer sun. Paint chips and fades; powder coat resists both.
- Height and picket spacing: 4′ is typical for a boundary fence, 5′ or 6′ for privacy and pool enclosures. Tighter picket spacing (under 4″) raises the cost per linear foot but reads more like a solid screen.
- Styles: Flat-top, spear-top, and ornamental with decorative rings or scrolls. Decorative panels run higher than flat panels, often 15 – 25% more per section.
- Gate and hardware: Standard walk gates vs. double-drive gates with heavier hinges and self-closing hardware. Drive gates need to be engineered for their span and are the single biggest line item to change on any aluminum quote.
- Color: Black is standard and cheapest to stock. Bronze, white, and custom colors carry a lead time and a small upcharge. If your HOA dictates a color, confirm it before the order goes in.
- Brands: We work with verified material partners and will spec a residential-grade CWS or comparable aluminum system based on your run length and wind exposure. The spec is written into the estimate so you know exactly what’s going in the ground.
What Aluminum Fence Costs in Dallas, TX
For a typical Dallas residential aluminum fence, expect $4,000 – $10,000 installed, gates and all. That’s the range for most single-family lots we quote here.
What pushes a job to the low end vs. the high end:
- Linear feet: The single biggest driver. A 100′ run sits in the low range; a 250′ boundary run pushes toward the top.
- Grade and slope: A flat lot is faster. Dallas lots with any grade require racked panels and sometimes stepped posts, which adds labor.
- Demo of an existing fence: If there’s an old wood or chain link run to pull and haul off, add time and disposal cost.
- Gate count and dimensions: Each walk gate is a line item. A double-drive gate with heavy-duty hardware can add a meaningful percentage to the total.
- HOA submittal complexity: Some HOAs require design drawings and site plans; we build that into the quote, but the timeline is on their clock.
- Mechanical post digging vs. hand digging: Most Dallas runs allow machine digging. Sites with known buried utilities or tight access require hand digging, which costs more.
What’s included in a written estimate: materials, labor, post-setting concrete, gates and hardware, haul-off of the old fence if there is one, HOA submittal preparation, and the workmanship warranty. What’s typically not included unless we quote it separately: landscape restoration beyond minor cleanup, sod replacement, gate automation (operators and wiring), and any electrical or irrigation work required to route around buried lines. Upfront pricing means the number you see is the number you pay, and we don’t open the job with a surprise.
See the difference
Before
After
Before
After
Before
AfterWhat Dallas Homes Do to an Aluminum Fence Job
Dallas is Blackland Prairie clay, and it changes how this job gets built. That clay swells and shrinks hard with the wet-dry cycle, and anything set in a shallow footing here will heave or lean within a few summers. On pre-war pier-and-beam bungalows in Oak Cliff and East Dallas, the ground around the house moves differently than the undisturbed soil at the property line, so we set aluminum posts deeper than the minimum to hold plumb. It’s the same movement that keeps foundation crews busy across the slab-on-grade ranch stock in neighborhoods like Casa Linda and the older stretches near White Rock Lake; a fence post has, in many ways, a harder job than a foundation pier because the load is on one side and the wind is on the other.
The other Dallas factor is wind. DFW sits in a high-wind zone, and severe spring straight-line storms and hail are a real annual event. An aluminum fence doesn’t rust or hail-crack the way some panels do, but a long run on an open lot takes real wind load. That’s why we spec heavier posts and correct spacing on open acreage properties rather than maxing the distance between posts to save on materials. HOAs in Highland Park, University Park, and the new infill subdivisions are also stricter than you might expect, and most require an approval before install; we handle that submittal as part of the job. Some neighborhoods also cap fence height at 4′ in front yards and 8′ in back, which is the kind of thing a Dallas contractor should catch before you buy a single section.
If the fence is one piece of a larger project – a new patio, a driveway redo, a pool enclosure – it often makes sense to sequence them together. Homeowners frequently pair this with Patios, Walkways & Pool Decks in Dallas, or with Driveway Repair & Replacement in Dallas, so heavy equipment is on site once instead of twice. If you’re planning the whole exterior from scratch, the wider scope lives on our Fence Installation in Dallas page. And if you’re outside the city limits, we also cover Dallas and the surrounding towns including Highland Park, University Park, Duncanville, and Irving.
Serving Dallas, TX – Our Local Coverage Area
We serve Dallas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Aluminum Fence in Dallas
Most Dallas residential aluminum fence jobs take 2 – 4 days of on-site work once the fence is ordered and the HOA approval (if required) is in hand. The order and approval stage can add 1 – 3 weeks, mostly depending on the HOA and material lead time. The on-site portion is fast because there’s no concrete cure delay beyond the initial post-setting. Call (844) 797-4808 for a firm timeline on your property.
Dallas residential fences generally don’t need a building permit when they’re under the city’s height threshold, but they still need to respect setback and sight-line rules, and HOAs almost always require approval before installation. The rules vary by lot and by neighborhood. We pull together the submittal and handle the paperwork. Call (844) 797-4808 and we’ll tell you what your specific property needs.
Usually yes. We call in utility locates before any digging, and irrigation lines can typically be routed around the post line rather than relocated. The main work is digging post holes at 6′ – 8′ on center and setting posts in concrete. If something is buried exactly where a post needs to go, we adjust the layout rather than move the line. Call (844) 797-4808 for an on-site assessment.
Most residential aluminum fence jobs in Dallas land between $4,000 and $10,000 installed, gates included. The number moves primarily with linear feet, gate count and size, panel grade, and whether there’s an old fence to demo. We give a written line-item quote so you can see what each piece costs. Call (844) 797-4808 to schedule your free estimate.
Every aluminum fence we install is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right, and that’s one of the longest workmanship guarantees in the residential construction space. The aluminum panels themselves also carry the manufacturer’s finish warranty on top of ours. You’ll get the warranty in writing before work starts. Call (844) 797-4808 with any questions about coverage.
Get a Free Aluminum Fence Estimate in Dallas
If you’re ready to price an aluminum fence in Dallas, the next step is a free on-site estimate. We walk the property, measure the run, check the grade, flag any HOA requirements, and hand you a written line-item quote with the full spec spelled out. Calls are answered by a live person 24/7 at (844) 797-4808, and there’s no voicemail and no waiting until Monday. $1,000 off projects over $10,000, 0% financing for 18 months, and a free design consult come standard.
Written by the team at Groundwork Construction Co.