Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Grand Prairie, TX: What It Costs and How Long It Takes
Metal roofing in Grand Prairie typically runs $15,000 to $40,000 installed, and most homes are finished in three to seven working days once the panels and trim are on site. That range covers a standard ranch or tract home in 75052 as well as a larger two-story build, and it depends mostly on roof size, panel type, and whether the old roof has to come off. Call (844) 797-4808 to schedule a free on-site estimate with a written, line-item quote.
Key takeaways:
- Installed metal roofs here run $15,000 – $40,000, and a written quote is fixed before crews start.
- Most jobs finish in 3 – 7 working days, weather permitting.
- Grand Prairie roofs face hail, high wind, and intense summer sun, so panel gauge and fastening matter more than finish color.
- You’ll get upfront pricing with no change orders and the 730-Day Done Right Promise on the workmanship.
How a Metal Roof Goes On, Stage by Stage
Metal roofing isn’t a one-day job, and the order of the stages matters as much as the panels. Here’s how the work actually sequences on a Grand Prairie home.
Stage 1: Tear-off and deck inspection (day 1)
We strip the existing shingles down to the deck and inspect the sheathing. On 1990s – 2010s tract homes in 75052, decking is usually solid. On older 75050/75051 houses, we find soft spots and sagging from years of heat and moisture. Any rotted sheathing gets replaced before anything goes back down. You decide here whether to add a synthetic underlayment upgrade.
Stage 2: Underlayment and ice-and-water barrier (day 1 – 2)
A high-temp synthetic underlayment goes down over the whole deck, with a peel-and-stick barrier in the valleys and along eaves. In North Texas heat, the underlayment grade matters, so we use one rated for the sun load. You don’t have to decide anything at this stage unless you want a specific brand.
Stage 3: Trim, flashing, and panel layout (day 2 – 4)
We set the drip edge, rake trim, and valley flashing, then lay out the panel runs so seams land where they should. Standing seam panels get roll-formed or pre-cut to length; exposed-fastener panels get screwed down on a measured grid. This is the longest stretch of work and where the precision shows. You approve panel color and profile before this stage begins.
Stage 4: Panel installation and fastening (day 3 – 6)
Panels go on in sequence with sealed laps and correctly torqued fasteners. Standing seam uses hidden clips that let the metal move with temperature; exposed-fastener panels use washer-head screws driven to spec. You pick the panel style and gauge in the estimate, not mid-job.
Stage 5: Final inspection and cleanup (day 6 – 7)
We check every penetration, ridge, and edge, run a magnet sweep for stray fasteners, and walk the job with you. Then we hand over the warranty paperwork and your documentation. When the metal roof is part of a full Roofing in Grand Prairie project, we sequence it so the rest of the work lines up.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
Most of the decisions happen before a single panel goes on. Here’s what actually changes the result, with honest trade-offs.
- Standing seam vs. exposed-fastener panels. Standing seam hides its fasteners under raised seams and lasts 40 – 70 years with minimal upkeep, but it costs more and requires more precise installation. Exposed-fastener panels are cheaper and faster to install, but the washers can back out over time and need checking. Standing seam suits homes you plan to keep; exposed-fastener suits tighter budgets.
- Panel gauge. Thicker 24-gauge steel resists hail dents and oil-canning better than 26-gauge. It costs more per square, but it holds up to Grand Prairie’s spring hail better.
- Material: steel vs. aluminum. Steel is the most common choice here for strength and price. Aluminum resists rust in humid conditions but dents more easily and costs more.
- Finish and color. A factory Kynar finish holds color through North Texas sun better than a standard polyester finish. Light colors reflect heat and help with summer cooling; dark colors look sharp but run hotter.
- Concealed vs. exposed fastener with insulation. A thermal break under the panels cuts attic heat gain. It adds cost but pays back in summer comfort.
Homeowners often pair this with Window Replacement in Grand Prairie to cut heat gain on the walls at the same time.
What Metal Roofing Costs in Grand Prairie, TX
Most Grand Prairie metal roofing jobs land between $15,000 and $40,000 installed. That’s the market range for this city, and a written estimate holds to it.
Five things move the number:
- Roof size and pitch. A simple gable on a 1,800 sq ft ranch sits at the low end. A steep, cut-up roof with dormers and valleys lands near the top.
- Existing roof condition. A tear-off adds labor and dump fees; if the old roof can be left and overlaid in some cases, cost drops, but we don’t over-apply where it isn’t right.
- Deck repairs. Rotted sheathing on older homes in 75050/75051 adds to the bill once we open it up. We flag this in the estimate as a line item, not a surprise.
- Panel type and gauge. Standing seam at 24-gauge costs more than exposed-fastener 26-gauge.
- Permit scope. A roof-only permit is straightforward; a re-roof tied to structural changes pulls in more inspection.
Your written estimate lists panels, underlayment, trim, fasteners, tear-off, disposal, and permit. What’s usually not included: structural repair if the deck is compromised, gutter replacement, or skylight replacement. We call those out before work starts.
See the difference
Before
After
Before
After
Before
AfterWhat Grand Prairie Homes Specifically Do to This Job
Grand Prairie straddles Dallas and Tarrant counties and sits on Blackland Prairie’s expansive clay. That one fact shapes metal roofing here more than any other. Each of the city’s four ZIPs (75050, 75051, 75052, 75053) has its own roof and foundation history, and the county line means permit and inspection procedures shift depending on which side of town the house sits. It’s a dual-county city, and few nearby suburbs combine both the clay movement problem and the two-county code friction in one jurisdiction.
The housing stock tells the rest of the story. Mid-century ranches and small post-war homes near the old downtown core in 75050/75051 have often had their roofs replaced twice already, so we find layered shingles and soft decking. The large 1990s – 2010s tract subdivisions in 75052 have original shingles nearing the end of their life and decking that’s still sound. On both, the heat and the drought-to-deluge rainfall cycles drive the wear. Spring hail and high wind are the recurring driver for re-roofs across the city.
One local wrinkle: on older slab-on-grade homes that have already been leveled once, a metal roof’s lighter weight can be an advantage, since it adds less load to a foundation that has moved. Our Roofing team factors that in when quoting. We also work the neighboring cities of Cedar Hill, Duncanville, Euless, and DeSoto, and our Grand Prairie service page covers the full area.
Serving Grand Prairie, TX – Our Local Coverage Area
We serve Grand Prairie and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Grand Prairie
Most jobs take 3 to 7 working days once materials are on site. A simple ranch roof runs toward the short end; a steep, cut-up roof or a job with deck repairs runs longer. Weather and permit timelines add a few days when they do. Call (844) 797-4808 for a schedule estimate on your home.
Yes. A re-roof requires a permit, and because Grand Prairie spans Dallas and Tarrant counties, the process depends on which side of the city you’re on. We handle the permit and the inspection. Call (844) 797-4808 and we’ll walk you through what’s needed.
Sometimes, but not always. If the existing shingles are sound and the deck is solid, an overlay can work, but it adds weight and hides problems. We recommend a full tear-off on most homes so we can inspect the deck, and we’ll tell you honestly which is right for yours. Call (844) 797-4808 for a free assessment.
Installed metal roofing in Grand Prairie runs $15,000 to $40,000, depending on size, panel type, and existing roof condition. Standing seam at the top of the range, exposed-fastener panels lower. Call (844) 797-4808 for an exact quote – estimates are free.
Panel manufacturer warranties cover the material, and our 730-Day Done Right Promise covers the workmanship – if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in residential construction. Call (844) 797-4808 to see it in writing.
Get a Free Metal Roofing Estimate in Grand Prairie
Call (844) 797-4808 and a live person picks up, day or night. We’ll set a time to walk your roof, measure it, and put a written line-item quote in your hands with fixed pricing and no surprises. You’ll also hear financing options: 0% for 18 months, and $1,000 off projects over $10,000. Homeowners often pair this with Impact Windows & Doors in Grand Prairie for added storm protection. The estimate is free, and there’s no pressure to sign.
Written by the team at Groundwork Construction Co.