Roofing
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Windows & doors
Driveway & pavers
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Specialty Roofing in Irving, TX: What It Covers and What It Costs
Specialty roofing in Irving means the work beyond a standard shingle tear-off: tile, standing seam metal, low-slope and flat assemblies, and the detailing that goes with them. Most specialty jobs run three to seven days on site, and pricing starts around $15,000 for metal work and climbs toward $40,000 on larger or more complex roofs, with tile repair landing between $600 and $2,500. Call (844) 797-4808 for a free on-site estimate.
How a Specialty Roofing Job Actually Runs, Start to Finish
Specialty work doesn’t move like a standard replacement. The sequence is tighter, the inspections are stricter, and a few decisions land in your lap early. Here’s what the week looks like.
Day 1: Tear-off, deck inspection, and the first decision
We strip the old assembly down to the deck and walk it with you. On specialty roofs this is where the job gets honest: soft sheathing, old underlayment, or a low-slope section that was never built right. You decide there whether we replace compromised decking (typically a per-sheet add) or repair and move on. Most Irving teardowns take a single day.
Day 2: Underlayment and flashing
This stage is where specialty roofs live or die. Tile and metal both depend on a water-shedding layer beneath them, so we install the membrane, then the valleys, penetrations, and wall flashings. Skipping detail here is the number one reason a tile roof leaks five years in. Budget a full day, sometimes more on a cut-up roofline.
Day 3 – 5: Panel or tile installation
Metal panels go down in runs from the eave up; tile sets course by course. Both are slower than shingles and less forgiving of shortcuts. On a North Texas roof we work early mornings through the summer heat, which stretches the schedule slightly on larger Irving homes.
Day 5 – 6: Ridge, trim, and accessory work
Ridge caps, hip and valley closures, and any vents or skylights get finished here. It’s also where we confirm the roof is ready for gutters and any solar conduit runs, which you’ll want mapped before final inspection.
Final inspection and walkthrough
We schedule the inspection, walk the roof with you, and hand over the paperwork. You decide at the start how much accessory work to fold in; by this point there’s no more choosing, only confirmation.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Be Choosing Between
- Standing seam metal: Long service life and clean lines, priced roughly $15,000 – $40,000 for most Irving homes. It handles hail better than most, but the upfront number is real and installation quality drives everything.
- Clay or concrete tile: The classic look for the region’s Spanish-influenced homes. Heavy, so it may need structural review on older South Irving builds, and repair pricing (roughly $600 – $2,500) depends on matching the existing tile profile.
- Low-slope and flat assemblies: Common on additions, porches, and some Las Colinas product. Membrane systems cost more per square but are the only right answer where pitch won’t shed water.
- Stone-coated steel: Tile look with metal behavior. Middle of the road on cost and a good fit if you want the profile without the weight.
- Underlayment grade: Synthetic versus premium self-adhering membrane. The upgrade is small relative to the whole job and matters most on low-slope edges.
If your project also involves exterior openings, homeowners often pair this with Energy-Efficient Windows in Irving so the envelope gets handled in one pass. Materials here come from established suppliers; Oldcastle and Quikrete products show up regularly in the flashing and masonry details on tile jobs.
What Specialty Roofing Costs in Irving, TX
Plan on $15,000 – $40,000 for metal roof installation, $600 – $2,500 for tile roof repair, and $8,000 – $20,000 as the general replacement band against which specialty quotes get measured. Five variables push a job toward one end or the other:
- Roof size and complexity: a simple gable costs far less per square than a cut-up hip roof with multiple valleys.
- Deck condition: soft sheathing or old battens add material and labor.
- Material weight and profile: tile may require a structural check; heavier systems cost more to install.
- Pitch and access: steep or hard-to-reach sections slow everything down.
- Permit scope: Irving requires a permit for a full re-roof, and structural changes add review time.
Your written estimate should spell out tear-off, underlayment, materials, and cleanup line by line. What it usually won’t cover until we open the roof: decking replacement, hidden rot, or structural repairs. Those get a separate written line before we touch anything, so there are no mid-job surprises.
See the difference
Before
After
Before
After
Before
AfterWhat Irving Homes Specifically Do to a Specialty Roof
Irving is really two construction markets stitched along the SH-114 corridor, and it shows up on every roof. South and central Irving, around ZIPs 75060, 75061, and 75062, is postwar brick-veneer ranch country, now full of teardown-rebuilds and additions where the original framing wasn’t built for a heavy tile roof. Out toward Las Colinas, Valley Ranch, and the 75063/75038 edge, you’re on denser, newer product and commercial-grade work tied to the airport and convention center. The other local fact that matters is the black-clay soil: the wet-dry cycle heaves foundations, and a shifting structure telegraphs into flashing, valleys, and ridge lines. Contractors used to other metros are surprised at how often a specialty roof here starts with a foundation or framing question, and we flag it before the first panel goes up. This work is frequently part of a full Roofing in Irving scope.
Serving Irving, TX – Our Local Coverage Area
We serve Irving and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Specialty Roofing in Irving
Most specialty roofs take three to seven days on site, depending on size, material, and weather. Tile and metal both move slower than shingles. Call (844) 797-4808 for a firm timeline on your roof.
Yes, a full re-roof and any structural change require a permit and inspection. We pull the permit and schedule the inspection ourselves. Call us and we’ll walk you through what your job needs.
Usually yes. The roof work itself doesn’t move plumbing, and we keep structure changes to a minimum unless the deck or framing demands it. If we find a structural issue, we tell you in writing before proceeding. Reach out for an assessment.
Metal runs $15,000 – $40,000, tile repair $600 – $2,500, and general replacement $8,000 – $20,000. Your exact number depends on size, deck condition, and material. Call (844) 797-4808 for a free line-item estimate.
Every specialty roof we install is backed by our 730-Day Done Right Promise: if it isn’t done right, we make it right. Manufacturer warranties on the panel or tile system apply on top. Call us to review the details for your project.
Get a Free Specialty Roofing Estimate in Irving
We’ll come out, walk the roof, and hand you a written, line-item estimate for specialty roofing in Irving at no cost. Call (844) 797-4808 and a live person answers any hour, any day. We’ll ask about the roof, the home’s age, and your timeline, then book a visit that fits your schedule. Projects over $10,000 get $1,000 off, and 0% financing runs 18 months. You can also see our broader Roofing work and pair the job with Sliding & Patio Doors in Irving. Upfront pricing, no surprises.
Written by the team at Groundwork Construction Co.