Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Wood Fence in Irving, TX: What It Costs and What You’re Actually Getting
A wood fence in Irving typically runs $3,500 to $9,000 for a standard residential lot, with most single-family backyard replacements landing between $4,200 and $6,800. Plan on a two- to four-day build once posts are set and materials are on site. Call (844) 797-4808 for a free on-site estimate – we’ll walk the property line with you and put a firm number in writing before any post goes in the ground.
What a Real Wood Fence Build Looks Like, Day by Day
The sequence below is how we run wood fence work in Irving – and the pace matters here because North Texas clay and summer heat both push the schedule around. Here’s what actually happens:
Stage 1: Property line walk and layout (about 1-2 hours)
Before digging, we confirm setbacks, property line position, and utility locates (water, gas, electric, cable). In South Irving’s older lots this is where surprises surface – old sprinkler runs, patio slabs poured against a fence line, or a shed footing that sits two inches into the setback. You’re deciding here: exact fence height, gate placement, and whether you want to match the neighbor’s existing line or step it in six inches to keep it inside your lot.
Stage 2: Demolition and post removal (half a day to a full day)
Old cedar or pine posts set in Irving’s black-clay soil often rot at the ground line long before the panel above looks bad. We pull them, remove the concrete footings, and dispose of everything. This is where you’ll want to walk the yard once more and decide if a gate moves or a panel angle changes while the ground is open.
Stage 3: Post setting (day 2)
We set posts in concrete with a minimum 24-inch depth and typically 30-inch spacing for 6-foot privacy runs. The clay here holds a post well but can shift during wet-dry cycles, so post depth and footing width aren’t places to shave cost. On a typical Irving lot, expect 25 to 45 posts depending on linear footage.
Stage 4: Rails, pickets, and framing (day 3)
Two or three rails per section, pickets aligned with a string line and spacing jig, and top caps only if you’ve chosen them. This is the longest single day. You’ll want to confirm picket style (dog-ear, flat-top, or French Gothic) and whether the finished side faces out or in.
Stage 5: Gates, hardware, and cleanup (half day)
Hinges, latches, and any self-closing hardware get installed and adjusted. We do a final walkthrough together before we pull off the site. That’s also when we hand off the 730-Day Done Right Promise in writing – if a post settles or a hinge works loose, we come back and fix it.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Wood Fence Options Worth Weighing Before You Pick
Most Irving buyers are choosing between four real categories. Here’s the honest trade-off on each:
- Cedar privacy fence (6 ft, 1×6 pickets): The default choice for most Irving yards. Cedar handles humidity and heat well, resists rot better than pine, and looks good without stain. Expect 10-15 years of real service life with basic upkeep. Higher upfront cost than pine.
- Pressure-treated pine: The budget option – around 20-30% less than cedar on comparable runs. The catch is that North Texas sun and clay drain it hard; untreated pine in direct sun may need staining within 18 months and can cup or warp on west-facing runs.
- Board-on-board cedar: Pickets overlap slightly for full privacy with no gaps. Costs 10-15% more than standard butting but eliminates the peeking problem on a 6-foot fence. Good fit for corner lots or homes with a neighbor’s pool nearby.
- Horizontal slat or shadowbox designs: A contemporary look with air gaps. Popular along Las Colinas and Valley Ranch lots where new build homes have modern architecture. The trade-off: less privacy and more visible fasteners over time.
Post, rail, and picket sizes matter too. A 6-foot privacy fence with 4×4 posts at 8-foot spacing is standard; 4×4 at 6-foot or 6×6 posts cost more but hold up longer on long uninterrupted runs with no windbreak. On the material side, we source from established suppliers and stand behind the grade we spec – if you’re adding a paver walkway or border along the fence line, homeowners often pair that job with Paver Driveways in Irving.
See the difference
Before
After
Before
After
Before
AfterWhat Wood Fence Costs in Irving, TX
For a typical Irving residential lot – 120 to 180 linear feet of 6-foot cedar privacy fence – you’re looking at $3,500 to $9,000 installed, and most jobs land around $4,500 to $6,500. Here’s what moves the number:
Four variables push a wood fence build toward the high end:
- Linear footage and height: 8-foot privacy fence costs roughly 25-35% more than 6-foot in material and labor. Corner lots and odd-angled yards add cuts and waste.
- Old fence removal and disposal: $300-$800 depending on length and whether the footings are easy to pull. Rotting posts in Irving’s clay sometimes require extra effort.
- Gates and hardware: Each walking gate adds $250-$600; driveway gates with heavier framing are $700-$1,400.
- Grade and drainage: Sloped yards in South Irving’s older neighborhoods mean stepped pickets or a retaining transition – $400-$1,200 extra depending on how much adjustment is needed.
- Material grade: Cedar over pine, board-on-board over butted, and heavy-duty hardware all shift the line-item total.
A written estimate from us includes demolition, disposal, all materials, concrete, hardware, and labor. What’s not typically included: HOA approval fees, permit fees if the city requires one, and landscaping repair around fence lines. If you’re also refreshing a driveway on the same property, we handle both – Concrete Driveways & Concrete Work in Irving runs on the same schedule.
What Irving Homes Specifically Do to a Wood Fence Job
Irving splits into two very different fence markets, and both come with their own quirks. In the mid-century core – South Irving around the old downtown, the Hospital District, and the 75062 strips off Story Road and Irving Boulevard – the housing stock runs 1950s-1970s brick-veneer ranches where the fence line usually sits on ground that’s been altered by 60-plus years of tree roots, old sprinkler lines, and slab additions. Post holes there regularly hit old concrete, and we plan for it.
On the Las Colinas, Valley Ranch, and 75063 side, fences run behind newer subdivisions and multifamily complexes, so HOA approval is usually part of the conversation before we dig. Clay soil is the constant: North Texas black clay swells and shrinks with the wet-dry cycle, so post depth and footing width matter more here than in sandy-soil markets. And when a fence sits on a lot where an addition or remodel happened, we’re often coordinating around existing Fence Installation in Irving scope on the same property. If you’re also considering Fence Installation as part of a larger yard plan, we can quote the whole scope together.
Serving Irving, TX – Our Local Coverage Area
We serve Irving and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Wood Fence in Irving
A standard 120-180 foot residential wood fence takes 2 to 4 working days from demolition to final cleanup. Larger runs, complex grades, or heavy demolition can push it to 5 days. Call (844) 797-4808 and we’ll give you a firm schedule in the estimate.
Most residential fences in Irving don’t require a permit, but height, setback from property lines, and HOA rules all affect whether yours does. Corner lots and fence lines over 6 feet are the most common trigger points. Call (844) 797-4808 and we’ll confirm what applies to your address before we quote.
Expect $3,500 to $9,000 installed for a standard residential lot, with most jobs landing around $4,500 to $6,500. Material grade, footage, gates, and old fence removal move the number. Call (844) 797-4808 for an exact written quote – estimates are free.
Yes, with proper post depth and footing width. The key failure we see in Irving is shallow-set posts that heave or lean after a wet spring. We set posts at a minimum 24-inch depth with concrete footings, and cedar handles the heat better than pine. Call (844) 797-4808 if you want a current fence inspected.
Every wood fence we build is covered by our 730-Day Done Right Promise – if a post settles or a hinge fails within that window, we make it right. The number you see on the estimate is the number you pay. Call (844) 797-4808 to schedule your free on-site estimate.
Whether you’re replacing a leaning cedar run in South Irving or fencing a new build out near Valley Ranch, the first step is a free walkthrough. We’ll measure the line, confirm setbacks and locate marks, and hand you a written, line-item estimate – no pressure, no surprises. We serve homeowners throughout Irving and the surrounding neighborhoods. Call (844) 797-4808 to schedule your free estimate; a live person answers 24/7, and we can typically get eyes on your property within the week.
Written by the team at Groundwork Construction Co.