Fence
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
Driveway & paversFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Dallas, TX: What It Costs and How Fast It Goes In
A chain link fence on a typical Dallas lot runs $3500 – $9000 for most residential jobs, and the work itself is usually two to four days from first post to final tension. Small front-yard runs sit at the low end; long side-and-rear property lines with height over six feet, a drive gate, or dense Blackland clay pushing post depths land at the top. Call (844) 797-4808 to set a free on-site estimate and get a written line-item number before anything is ordered.
How a Chain Link Fence Goes In, Stage by Stage
We’ve done this enough in Dallas to know where a chain link job goes sideways: usually in the ground, not in the fence. Here’s the actual sequence.
Day 1, morning: layout and utility locates
Before a single post goes in, we walk the property line with you and mark corners, gates, and terminal posts. The 811 call for buried utilities is placed and the dig waits for the all-clear – this is non-negotiable in a city where gas, irrigation, and old cable runs cross residential lots constantly. This is where you decide the gate locations and swing direction, and it’s the cheapest time to change your mind.
Day 1 – 2: post holes and concrete setting
Line posts on a Dallas chain link job get set in concrete, not tamped dirt, and that matters more here than most homeowners expect. Terminal posts – corners, ends, and gate posts – carry the tension of the whole run and get wider holes and deeper embedment. On the expansive clay most Dallas lots sit on, we set posts deeper than you’d see on sand or limestone ground, because a post footed for still soil will lift and lean after a couple of wet-dry cycles. The concrete has to cure before tension goes on; that gap is real time, not padding.
Day 2 – 3: rails, mesh, and tension
Top rail, tension bands, and mesh get pulled once the concrete is set. This is the part that separates a fence that stays tight from one that sags within two summers. You’ll choose your mesh gauge and coating before this stage, so make that call at the estimate.
Day 3 – 4: gates, hardware, and walkthrough
Gate frames get hung, hinges and latches set, and we walk the whole run with you – checking tension, gate drop, and post plumb. Any adjust happens now, on our dime.
After the crew leaves
We hand over a written record of post depths and concrete specs. That paperwork matters if you ever sell, and it’s part of how our Fence Installation work is documented across Dallas.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Chain Link Options You’ll Choose Between
Chain link is not one product. The choices below move both the price and how long the fence looks new.
- Mesh gauge: 11.5-gauge is the builder-standard, lighter and cheaper; 9-gauge is heavier and resists bending from kids, dogs, and hail-driven debris better. Worth the upgrade on any run you plan to keep a decade or more.
- Coating: Galvanized is the budget choice and holds up fine in dry stretches; vinyl-coated (usually black or green) costs more but hides rust at the bottom rail and reads cleaner against landscaping. Black vinyl-coated is the popular pick on Dallas streets where fences face the front.
- Height: 4-foot and 5-foot are common for front yards and decorative runs; 6-foot is the residential default for back property lines; 7 – 8-foot shows up on corner lots and where a pool or dog run needs it.
- Gate type: Walk gates versus drive gates with cantilever or dual-swing hardware. Drive gates add cost fast because the posts and frame carry far more load.
- Top rail and tension wire: A tension wire along the bottom keeps mesh from curling up; skip it and the bottom edge waggles within a year. We include it unless you tell us not to.
Concrete for post footings comes from proven mixes – Quikrete, Sakrete, and Oldcastle products all show up on our Dallas jobs, and we spec the mix to the soil and post load rather than grabbing whatever’s on the shelf.
What a Chain Link Fence Costs in Dallas, TX
The realistic range for a residential chain link job in Dallas is $3500 – $9000. Here’s what moves a job to the low or high end.
- Linear footage and height: The biggest single driver. A short front run at 4 feet versus a full perimeter at 6 feet can triple the number.
- Gate count and type: Each walk gate adds cost; a drive gate with proper hardware can add a meaningful chunk on its own.
- Mesh gauge and coating: 9-gauge vinyl-coated mesh is the high end; 11.5-gauge galvanized is the low.
- Site conditions: Rock, roots, old fence removal, and tight access all add labor. On Dallas clay, post depth and concrete volume are baked into the number – this is where a cheap bid usually hides its shortcut.
- Permits and HOA approvals: Where a permit or HOA architectural review is required, that adds time and paperwork cost.
A written estimate should list footage, height, gauge, coating, gate specs, post depth, concrete, removal, and disposal as separate lines. What it typically excludes: utility relocation, grading, and any landscape repair beyond reseeding. Call (844) 797-4808 for an exact quote – estimates are free.
See the difference
Before
After
Before
After
Before
AfterWhat Dallas Homes Specifically Do to This Job
Dallas sits on the Blackland Prairie, and its clay soil swells and shrinks with the wet-dry cycle in a way that changes how fence posts have to be set. A post footed for still ground will heave and lean after a couple of dry summers – which is exactly why we go deeper and wider on terminal posts here than crews do on the limestone ground to the south or the sandy Piney Woods to the east. Combined with DFW’s high-wind-zone code and the spring straight-line storms that roll through, fence runs here get designed for wind uplift and soil movement, not frost.
The housing stock shapes the work too. Older pier-and-beam bungalows in East Dallas and Oak Cliff often have property lines that don’t match the plat, so we measure before we order. The slab-on-grade ranch tracts built through the 1950s – 70s and the new infill builds bring their own quirks – narrow side yards, shared drive aprons, and HOA review in the newer master-planned pockets. Where a run meets a driveway or slab edge, homeowners often pair this with Concrete Driveways & Concrete Work in Dallas or Asphalt Driveways & Resurfacing in Dallas so the apron and fence line get done together. If the chain link is one piece of a larger outdoor plan, it’s often part of a full Fence Installation in Dallas scope. We cover Dallas and the surrounding neighborhoods, including Highland Park, University Park, Duncanville, and Irving.
Serving Dallas, TX – Our Local Coverage Area
We serve Dallas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked About Chain Link Fence in Dallas
Most residential chain link jobs in Dallas take two to four working days, with the concrete cure between post setting and tension being the biggest variable. Larger runs with multiple gates and old fence removal push toward the longer end. Call (844) 797-4808 for a timeline on your specific lot.
It depends on height, location, and whether your lot sits in an HOA or historic overlay – many residential chain link runs don’t require a permit, but front-yard and corner-lot runs often do. We check the requirement for your address during the estimate so you’re not guessing. Call us to sort it out before you order materials.
Usually yes – the fence line runs the property edge, and the 811 locate tells us where to shift a post rather than move a utility. If a post lands directly on a gas or irrigation line, we reposition within code rather than relocate the line. Call (844) 797-4808 and we’ll walk your lot with you.
Expect $3500 – $9000 for a typical residential job, with the low end on short runs and the high end on full perimeters at 6 feet with drive gates. Site conditions and mesh grade move the number most. Call for a free on-site estimate – the number we write is the number you pay.
Every chain link job we do is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. That covers workmanship on post setting, tension, and gate hardware. Call (844) 797-4808 with any question about coverage before or after the job.
Get a Free Chain Link Fence Estimate in Dallas
Call (844) 797-4808 for a free on-site estimate on your chain link fence in Dallas. A live person answers around the clock, and we’ll set a time that works. On the visit we measure the run, check where the utilities sit, confirm HOA or permit requirements for your address, and hand you a written line-item quote – no pressure, no surprises, and 0% financing for 18 months if you decide to move forward.
Written by the team at Groundwork Construction Co.