Driveway & pavers
Kitchen remodeling
Bathroom remodeling
Home additions & ADU
Roofing
Windows & doors
FenceFree written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Asphalt Driveways & Resurfacing in Irving, TX: What It Costs and How Long It Takes
Asphalt Driveways & Resurfacing in Irving, TX runs $3,500 – $9,000 for a full new asphalt drive, and a resurface (overlay) on sound pavement typically lands well below a full replacement. Most residential drives are torn out and repaved in two to three working days; resurfacing can be a single day once the base is proven. Call (844) 797-4808 and we’ll walk the drive with you and put a written number in your hand.
From first cut to final roll: how an Irving asphalt job actually runs
Asphalt work is fast on the surface and unforgiving underneath. The base is where a driveway either lasts fifteen years or fails in three, and in North Texas that base is fighting black clay the whole time. Here’s the sequence we run.
Stage 1: Walk-through and base assessment (day of estimate)
We probe the existing base, check for soft spots, look at how water drains off the slab, and measure the square footage and thickness. You decide then whether you’re repairing, resurfacing over what’s there, or starting clean. If the base is pumping or the cracking runs in an alligator pattern, resurfacing is money thrown away and we’ll tell you so.
Stage 2: Demolition and haul-off (day 1, most of the morning)
Old asphalt or failed concrete comes out with a skid-steer and goes straight into a dumpster. On a typical 500-square-foot Irving drive, demo and haul-off run three to four hours. You decide on the spot where the dumpster sits and whether any landscaping along the edges needs protecting.
Stage 3: Grading, base, and compaction (day 1 into day 2)
We cut the grade to shed water away from the garage and foundation, then lay and compact the base in lifts, usually 4 to 6 inches of crushed stone on a residential drive. Compaction happens in passes with a plate or roller, not one lazy go-round. This is the stage where a driveway is won or lost, and it’s the one most bids quietly skip.
Stage 4: Hot-mix laydown and rolling (day 2)
Hot mix arrives from the plant and gets placed and rolled while it’s still workable, typically 2 to 3 inches compacted for a residential drive. You decide the thickness and mix grade up front, because once it’s on the ground that choice is locked. Edges get tamped and finished by hand.
Stage 5: Cure and return to service (days 2 through 30)
The drive is walkable within a day and drivable in 48 to 72 hours in warm weather, but full cure takes weeks. Keep heavy trucks and sharp-turned wheels off it for the first month. A seal coat goes on after the asphalt has cured, not before.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The choices you’ll be making, and what each one really costs you
Most of the decisions on an asphalt drive come down to five things. Here’s the honest trade-off on each.
- Full replacement vs. resurfacing: A new drive runs $3,500 – $9,000. An overlay is cheaper but only works when the base is sound and the cracking is cosmetic. Over a failing base, an overlay buys you two or three years at best.
- Base depth and stone grade: 4 inches of compacted base suits a passenger-car drive; 6 inches handles an F-150 or a boat trailer without rutting. The extra stone is a modest line item and the cheapest insurance on the job.
- Asphalt thickness: 2 inches compacted is standard residential; 3 inches is worth it on a wide drive or one that sees regular truck traffic. Thin asphalt over clay is how you get reflective cracks by year four.
- Hot-mix grade: Standard TxDOT-rated mixes are what we specify here. A coarser mix can hold up better in heat; a finer mix gives a smoother finish. Oldcastle and Quikrete products show up on the base and patch side of these jobs.
- Seal coat timing: Sealing too early traps solvent and softens the surface. We usually recommend waiting a full season post-install before the first seal.
What Asphalt Driveways & Resurfacing costs in Irving, TX
For a standard residential drive in Irving, asphalt paving runs $3,500 – $9,000, and a full driveway replacement that includes tear-out and new base runs $5,000 – $14,000. Resurfacing on sound pavement sits at the lower end of the paving range; once you’re pulling out failed base and re-grading, you’re in replacement territory.
Five variables push a job toward the top of that range:
- Square footage: a 400-square-foot single-car drive and an 800-square-foot double with a turnaround are two different jobs.
- Existing condition: soft base, alligator cracking, or a drive poured right against the slab all add demo and re-grading time.
- Access: a narrow side yard or a drive behind a fence gate slows the skid-steer and adds labor hours.
- Drainage corrections: if water currently runs toward the garage, the grade fix is real work, not a line item to wave away.
- Thickness and base upgrades: more stone, thicker asphalt, higher-grade mix.
A written estimate from us breaks out demo, haul-off, base, asphalt, and finishing as separate lines, with the number you see being the number you pay. What it won’t include unless you ask: landscaping repair along the edges, a new apron at the street, or seal coating after cure.
See the difference
Before
After
Before
After
Before
AfterWhat Irving homes do to this job
Irving is really two construction markets running side by side. South and central Irving, around the old downtown and Hospital District in the 75062 corridor, is 1950s-to-1970s brick-veneer ranch country, and a lot of those drives have been patched, re-patched, and patched again over sixty years of black-clay movement. The clay is the story here: it swells when it’s wet and shrinks in August, and it will crack asphalt that wasn’t laid over a properly compacted base. On the Las Colinas and Valley Ranch side, the driveways are newer, but tight lots and HOA oversight change the job, and we plan dumpster placement and laydown timing around those rules. Neighbors in nearby Farmers Branch and Coppell deal with the same clay, which is why the base spec matters more than the asphalt brand.
Most of what we see on older South Irving drives is edge failure first, then reflective cracking from underneath. Once a drive hits that stage, a $500 seal coat won’t stop it. For a broader picture of how the drive ties into the rest of the exterior, see our Driveway & Pavers in Irving page. Homeowners often pair a repaved drive with a New Detached ADU in Irving project, and if you’re expanding the usable footprint another way, a Junior ADU & Interior Conversion in Irving is a common companion.
Serving Irving, TX – Our Local Coverage Area
We serve Irving and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: Asphalt Driveways & Resurfacing in Irving
A full replacement runs two to three working days from demo to final roll, with 48 to 72 hours of cure before you drive on it. Resurfacing on a sound base is usually a single day. Weather is the one thing that can push it, since hot mix wants dry conditions and North Texas summer heat means early-morning pours.
Typically no permit is required for standard residential driveway paving or resurfacing on your own lot. That changes if you’re altering the approach at the street, cutting a new curb, or changing drainage onto a neighbor’s property, and those cases get reviewed. We’ll tell you up front what applies to your address before any work begins, and we don’t start without confirming it.
Resurfacing lands at the lower end of the $3,500 – $9,000 paving range for a standard residential drive. If we walk the property and find a soft base or alligator cracking, an overlay won’t hold, and we’ll quote a replacement in the $5,000 – $14,000 range instead. Estimates are free and there’s no pressure either way. Call (844) 797-4808 for an exact quote.
Every asphalt driveway and resurfacing project we run is covered by the 730-Day Done Right Promise: if it’s not done right, we make it right. That’s one of the longest workmanship guarantees in the residential construction space. Materials carry their own manufacturer terms, and your written estimate spells out both.
Because the crack is almost always a base problem showing at the surface. Irving’s black clay moves seasonally, and if the base under the asphalt wasn’t compacted and graded to shed water, patching the top is treating a symptom. Real fix means cutting back to sound base, re-grading, and repaving.
If the drive also needs new edging, an apron replaced, or you’re planning the wider exterior scope, that lives on the Driveway & Pavers hub, and our Irving service page lays out how we cover the ZIPs we serve. We’re not a single-job shop either, so a driveway that gets repaved often gets bundled with other exterior work.
Get a written number on your Irving driveway
We’ll come out, probe the base, look at drainage, and put a line-item written estimate in your hands for asphalt paving or resurfacing on your Irving property. Calls are answered by a live person 24/7, background-checked technicians arrive in uniform, and the number you see is the number you pay. Call (844) 797-4808 to schedule your free estimate.
Written by the team at Groundwork Construction Co.